Roemheld WM-020-369-10-en BA Скачать руководство пользователя страница 10

  

WM-020-369-10-en

 BA SPEEDY classic 2 balance

.doc

  

 

 

 

 

 

STARK Spannsysteme GmbH – Roemergrund 14 - 6830 Rankweil - Austria 

Tel.:+43 5522 37400-0 - Fax.:+43 5522 37400-700 - e-mail: 

[email protected]

 - 

www.stark-inc.com

  

10/16 

7  Start-up, operating and operation 

 

7.1  On putting into operation for the first time 

 

Visually inspect the entire machine and the fast closing clamp 

Instruct unauthorised personnel to leave the machine 

Check the fill levels of hydraulic oil. 

Check the depth dimension A (see Chapter "8.1 Check

 

dimension

 A

"). 

Check the fast closing clamp for hydraulic and pneumatic sealing. 

 

7.2  Function check 

 

When all clamping elements connected to the same circuit are fitted as described and tightened to 

the appropriate tightening torque, connect the hydraulic pressure generator to the circuit. 

 
 

Release: Slowly and carefully increase the hydraulic pressure to the release pressure. During this 

process check the clamping elements for leaks. If a leak occurs, immediately switch off the pressure 
generator and eliminate the leak. 

 

7.3  Operating and operation 

 

     Only pressurise the fast closing clamp for the changing process. 

Comment : 

do not leave

 the machine under continuous pressurise. 

Adjust the release pressure of the fast closing clamp overpressure safety valve to max. 5 bar 
above the maximum operating pressure. Adjust the operating pressure of the fast closing clamps 

(see Chapter 9 "Specifications"). 
 

 

7.4  SPEEDY with blow-out function 

First apply air pressure 

After approx. 3 s release SPEEDY 

Change pallet / clamp SPEEDY 

Only now switch off air 

 

Ensure an adequate air supply is provided.  

Type:  

Air flow rate l/min 

SPEEDY classic 2 Twister 

80 

 

Содержание WM-020-369-10-en BA

















Отзывы: