Chapter 10
120
V1: 0-15 V2: 0-15
The first parameter allows you to set the velocity threshold for Tone 1. Press [NEXT] to select this
parameter. Use the [+]/[-] buttons to set the threshold level. Press [NEXT] to select the V2 parameter; the
velocity offset for Tone 2 after the threshold is reached. Use the [+]/[-] buttons to set the offset level.
[AFTERTOUCH] Button
Aftertouch is modulation added by exerting pressure on a keyboard key after it has already been pressed
down (i.e. at the bottom of the key travel). The aftertouch effect can be used as a controller on the W-5000's
Lower manual only. Aftertouch is assigned under the [CONTROLS] button. The [AFTERTOUCH] button in
the EFFECTS section is an on/off switch for this function.
[GENERAL REVERB] Parameters
These parameters affect the reverb settings. Press the [GENERAL REVERB] button in the EFFECTS section
to access these parameters:
General Reverb
Type: Room 1, Room 2, Room 3, Hall 1, Hall 2, Plate, Delay, Pdelay
This parameter allows you to select the type of reverb you'd like to use. Each type simulates a different kind
of enclosed space with different characteristics. Use the[+]/[-] buttons.
Level: 1-127
This parameter allows you to set the level of post-reverb signal (the processed or 'wet' signal) being mixed
with the dry (straight) signal. Press [NEXT] to select this parameter. Set the return level with the [+]/[-] (or
[++]/[--]) buttons.
Filter: 0-7
This parameter allows you to set the pre-LPF frequency. (A Low Pass Filter is a kind of tone control which
filters out frequencies above a set point.) Press [NEXT] to select this parameter. Use the [+]/[-] buttons.
Time: 0-127
This parameter allows you to set the reverb time (the time it takes the reverb sound to decay). Press [NEXT]
to select this parameter. Use the[+]/[-] (or [++]/[--]) buttons to set the reverb time.
Feedback: 0-127
This parameter allows you to set the feedback level. Press [NEXT] to select this parameter. Use the[+]/[-] (or
[++]/[--]) buttons to set the feedback level.
Chorus Send: 0-127
This parameter allows you to set the amount of post-reverb signal being mixed back into the chorus input.
Press [NEXT] to select this parameter. Use the [+]/[-] (or [++]/[--]) buttons.
[SYNTH CHORUS] Parameters
These parameters affect the chorus settings. Press the [SYNTH CHORUS] button in the EFFECTS section to
access these parameters:
Synth Chorus
Level: 1-127
This parameter allows you to set the level of post-chorus signal (the processed or 'wet' signal) being mixed
with the dry (straight) signal. Press [NEXT] to select this parameter. Set the return level with the [+]/[-] (or
[++]/[--]) buttons.
Содержание W-5000
