Rockwell ShopSeries RK7032, Руководство пользователя

Страница: 8 / 32

DRILL PRESS ENG
8
C. FOR aLL TOOLS aS aPPLICabLE
1. KEEP GUARDS IN PLACE and in working order.
2. REMOVE ADJUSTING KEYS AND WRENCHES. Form
habit of checking to see that keys and adjusting
wrenches are removed from tool before turning it
on.
3. KEEP WORK AREA CLEAN. Cluttered areas and
benches invite accidents.
4. DON’T USE IN DANGEROUS ENVIRONMENT. Don’t use
power tools in damp or wet locations, or expose
them to rain. Keep work area well lighted.
5. KEEP CHILDREN AWAY. All visitors should be kept
safe distance from work area.
6. MAKE WORKSHOP KID PROOF with padlocks,
master switches, or by removing starter keys.
7. DON’T FORCE TOOL. It will do the job better and
safer at the rate for which it was designed.
8. USE RIGHT TOOL. Don’t force tool or attachment to
do a job for which it was not designed.
9. uSE PROPER EXTENSION CORD. Make sure your
extension cord is in good condition. When using
an extension cord, be sure to use one heavy
enough to carry the current your product will
draw. An undersized cord will cause a drop
in line voltage resulting in loss of power and
overheating. Table 1 shows the correct size to use
depending on cord length and nameplate ampere
rating. If in doubt, use the next heavier gage. The
smaller the gage number, the heavier the cord.
10. WEaR PROPER aPPaREL. Do not wear loose
clothing, gloves, neckties, rings, bracelets, or
other jewelry which may get caught in moving
parts. Nonslip footwear is recommended. Wear
protective hair covering to contain long hair.
11. aLWayS uSE SaFETy GLaSSES. also use face or
dust mask if cutting operation is dusty. Everyday
eyeglasses only have impact resistant lenses,
they are NOT safety glasses.
12. SECURE WORK. Use clamps or a vise to hold work
when practical. It’s safer than using your hand
and it frees both hands to operate tool.
13. DON’T OVERREACH. Keep proper footing and
balance at all times.
14. MaINTaIN TOOLS WITh CaRE. Keep tools sharp
and clean for best and safest performance.
Follow instructions for lubricating and changing
accessories.
15. DISCONNECT TOOLS before servicing; when
changing accessories, such as blades, bits,
cutters, and the like.
16. REDuCE ThE RISK OF uNINTENTIONaL STaRTING.
Make sure switch is in off position before
plugging in.
17. uSE RECOMMENDED aCCESSORIES. Consult the
owner’s manual for recommended accessories.
The use of improper accessories may cause risk
of injury to persons.
18. NEVER STAND ON TOOL. Serious injury could
occur if the tool is tipped or if the cutting tool is
unintentionally contacted.
19. ChECK DaMaGED PaRTS. before further use of
the tool, a guard or other part that is damaged
should be carefully checked to determine that it
will operate properly and perform its intended
function – check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting, and any other conditions that may
affect its operation. A guard or other part that
is damaged should be properly repaired or
replaced.
20. DIRECTION OF FEED. Feed work into a blade or
cutter against the direction of rotation of the
blade or cutter only.
21. NEvER LEavE TOOL RuNNING uNaTTENDED. TuRN
POWER OFF. Don’t leave tool until it comes to a
complete stop.
Figure 1
Grounding methods
GROUNDING
PIN
ADAPTER
GROUNDING
MEANS
GROUNDING
PIN
METAL SCREW
COVER OF GROUND
OUTLET BOX