Rockwell powerflex 700h Скачать руководство пользователя страница 41

Страница: 41 / 120

Component Test Procedures

2-9

Checking the Rectifying
Module (on AC Input Drives
Only)

Important:

This procedure requires special equipment and training. Only
qualified and trained personnel should perform these
procedures.

There is a series A and series B Rectifying circuit board. The tests you can
perform and the results of those tests vary depending on which series of
board is in your drive.

Remove power from the drive. Refer to

Removing Power from Drive on

page 3-3

Remove the covers from the power structure. Refer to

Removing the

Covers from the Power Structure on page 3-15

Remove the Power Structure from the enclosure. Refer to

Removing the

Power Structure from the Drive Enclosure on page 3-27

Visually inspect the pre-charging resistors. If the pre-charging resistors
are damaged:

Replace the Rectifying Module (Refer to

Removing the

Right-Side Output Power Module and Rectifying Module on
page 3-36

Check the rectifiers and external connections for short-circuits.

Check the Output Power Modules (Refer to

Conducting

Forward and Reverse Biased Diode Tests for Major Power
Components on page 2-3

Verify that the plugs on the cable that connects X13 on the Rectifying
Board to X2 on the ASIC Board are properly seated.

Verify that the jumper at X50 on the Rectifying board is in place.

Taking Measurements on Rectifying Module

Disconnect connectors X13, X12, X11 and X10.

Perform resistance measurements, using a digital multimeter, on the
points listed in

Table 2.I on page 2-10

Table 2.J on page 2-10

(on AC

Three-Phase drives). These points are on the back of the X10, X11 and
X12 plugs which you have disconnected from the board.

If the

Rectifying Module fails any of these tests, replace it

(Refer to

Removing the Right-Side Output Power Module and Rectifying
Module on page 3-36

)

Voltage Class

Rectifying Circuit Board Catalog String
Series A

Series B

400/480V AC

20-VB00459

20-VB00461

600/690V AC

20-VB00460

20-VB00462

Содержание powerflex 700h

























































































































Результаты поиска

Содержание powerflex 700h

Отзывы:

Похожие инструкции для powerflex 700h

Бренды по названию

Популярные бренды

Rockwell powerflex 700h, Руководство по обслуживанию

Результаты поиска

Содержание powerflex 700h

Отзывы:

Похожие инструкции для powerflex 700h

Бренды по названию

Популярные бренды