Rockwell PowerFlex 7000, Справочное руководство

Страница: 23 / 68

Rockwell Automation Publication SYSLIB-RM056B-EN-P - February 2017 23
PowerFlex 7000 Drive (P_PF7000)
Nrdy_Disabled BOOL 1 = Device not ready due to the following:
• Device disabled by Maintenance
• Configuration error
• Interlock not OK
• Permissive not OK
• Operator Stop priority command requires reset
• Device failure (shed requires reset),
• I/O Fault (shed requires reset)
• Device tripped (Drive Fault)
• Drive not ready
• Device logic disabled/no mode.
Nrdy_CfgErr
Nrdy_Intlk
Nrdy_Perm
Nrdy_OperPrio
Nrdy_Fail
Nrdy_IOFault
Nrdy_Trip
Nrdy_DriveNR
Nrdy_NoMode
Sts_MaintByp BOOL 1 = Maintenance bypass is active, display icon.
Sts_AlmInh BOOL 1 = Alarm is shelved, disabled, or suppressed, display icon.
Sts_MsgErr BOOL 1 = Message error, unable to read at least one non-RPI drive parameter.
Sts_Err BOOL 1 = Error in configuration: See detail bits for reason.
Err_Timer BOOL 1 = Error in configuration: Invalid check or reset pulse time (use 0…2,147,483).
Err_Sim BOOL 1 = Error in configuration: Simulation timer preset (use 0…2,147,483).
Err_Alarm BOOL 1 = Error in configuration: Alarm minimum On time or severity.
Err_FdbkEU BOOL 1 = Error in configuration: Speed Fdbk EU Min = Max.
Err_RefLim BOOL 1 = Error in configuration: Speed Ref Limit Min > Max.
Err_RefEU BOOL 1 = Error in configuration: Speed Ref EU Min = Max.
Sts_Hand BOOL Mode.Sts_Hand 1 = Mode is Hand (supersedes Maintenance, Override, Program, Operator).
Sts_Maint BOOL Mode.Sts_Maint 1 = Mode is Maintenance (supersedes Override, Program, Operator).
Sts_Ovrd BOOL Mode.Sts_Ovrd 1 = Mode is Override (supersedes Program, Operator).
Sts_Prog BOOL Mode.Sts_Prog 1 = Mode is Program (auto).
Sts_Oper BOOL Mode.Sts_Oper 1 = Mode is Operator (manual).
Sts_ProgOperLock BOOL Mode.Sts_ProgOperLock 1 = Program or Operator has requested mode lock.
Sts_NoMode BOOL Mode.Sts_NoMode 1 = No mode (disabled because EnableIn is false).
Sts_MAcqRcvd BOOL Mode.Sts_MAcqRcvd 1 = Maintenance acquire command received this scan
Sts_FailToStart BOOL FailToStart.Inp 1 = Drive failed to start.
Sts_FailToStop FailToStop.Inp 1 = Drive failed to stop.
Sts_IntlkTrip IntlkTrip.Inp 1 = Drive was stopped by an interlock not OK (one-shot).
Sts_DriveFault DriveFault.Inp 1 = Drive Fault (see drive display or manual).
Sts_IOFault IOFault.Inp I/O Communication fault status:
0 = OK
1 = Bad
Ack_FailToStart BOOL FailToStart.Ack 1 = Fail to Start, Fail to Stop, Interlock Trip, Drive Fault, or I/O Fault alarm has been
acknowledged.
Ack_FailToStop FailToStop.Ack
Ack_IntlkTrip IntlkTrip.Ack
Ack_DriveFault DriveFault.Ack
Ack_IOFault IOFault.Ack
Table 9 - P_PF7000 Drive Output Parameters
Output Parameter Data Type Alias For Description