Rockwell Automation Trusted TMR 24V DC страница 39 Скачать руководство пользователя

Страница: 39 / 43

Rockwell Automation Publication ICSTT-RM451D-EN-P - March 2021

Chapter 7

Specifications

This table lists the module specifications:

Item

Description

Backplane (IMB) Supply

Voltage

20V DC to 32V DC

Power

26 W

Field Supply

Voltage

18V DC to 58V DC

Maximum Current

30 A

Power Dissipation

Field Supply at maximum power group current.

36 W

System Supply

26 W

Module Location

T8100, T8300 I/O Module Slot

Isolation

Power Group to Power Group

50V Reinforced (continuous)

[Type tested at 1411V DC for 60 s].

Field Common

50V Reinforced (continuous)

250V Basic (fault)

[Type tested at 2436V DC for 60 s].

Channel to Channel

None

Fusing

Not user serviceable

Number of Outputs

Number of Power Groups

5
Each Power Group comprises 8 channels

Output

Output On State resistance

1.6 Ω

Maximum Current Rating (Continuous)

0.75 A per channel

Minimum On State Load Current

25 mA

Current Measurement Range

0 A to 1.35 A ±5% / ±5 mA

Voltage Measurement Range

0V DC to +58V DC ±2V DC

Maximum Withstanding

-1V DC to +60V DC

Channel to Channel Crosstalk

< 1%

Maximum Load Capacitance

500 μF

Output Short Circuit Protection

Electronic latching

Sequence of Events

Event Resolution (LSB)

1 ms

Time stamp Accuracy

±10 ms

50 Vrms Secondary circuit derived from Mains, OVC II up to 300V.

250 Vrms Mains circuit, OVC II up to 300V. Exposure to voltages at these levels shall

be temporally constrained consistent with the system MTTR.

Tolerance is ±5 mA up to 0.9 A, thereafter is ±5%.

Содержание Trusted TMR 24V DC












































Результаты поиска

Содержание Trusted TMR 24V DC

Отзывы:

Похожие инструкции для Trusted TMR 24V DC

Бренды по названию

Популярные бренды

Rockwell Automation Trusted TMR 24V DC, Оригинальное руководство пользователя

Результаты поиска

Содержание Trusted TMR 24V DC

Отзывы:

Похожие инструкции для Trusted TMR 24V DC

Бренды по названию

Популярные бренды