Rockwell Automation Allen-Bradley MP-Series Скачать руководство пользователя | Manualshive

Страница: 9 / 68

background image

MP-Series Heavy Duty Electric Cylinders

9

Rockwell Automation Publication MPAI-IN001E-EN-P - March 2012

Build and Route Cables

Knowledgeable cable routing and careful cable construction improves system electromagnetic

compatibility (EMC).
To build and install cables, perform these steps.

1.

Keep wire lengths as short as physically possible.

2.

Route signal cables (encoder or serial) away from motor and power wiring.

3.

Separate cables by 0.3 m (1 ft) minimum for every 9 m (30 ft) of parallel run.

4.

Ground both ends of the encoder cable shield and twist the signal wire pairs to prevent

electromagnetic interference (EMI) from other equipment.

Install the Electric Cylinder

The installation must comply with all local regulations and use of equipment and installation

practices that promote electromagnetic compatibility and safety.

Follow these steps to prepare the electric cylinder for installation on the machine.

1.

Provide sufficient clearances in the area of the electric cylinder for it to stay within its

specified operating temperature range.
Refer to

for the operating temperature range. Do not enclose

the electric cylinder unless forced air is blown across the electric cylinder for cooling.

Keep other heat producing devices away from the electric cylinder.

2.

Make sure the mounting surface supports the electric cylinder evenly so that it is free of

mechanical stress and distortion.

•

Evenness of the mounting surface must be within 0.127 mm (0.005 in.).

•

The thrust rod must be parallel to the guide within 0.0254 mm (0.010 in.).

ATTENTION:

High voltage can be present on the shield of a power cable, if the shield is not

grounded.
Make sure there is a connection to ground for any power cable shield.
Failure to observe these safety precautions could result in personal injury or damage to equipment.

ATTENTION:

Unmounted electric cylinders, disconnected mechanical couplings, and disconnected

cables are dangerous if power is applied.
Appropriately identify (tag-out) disassembled equipment, and restrict (lock-out) access to
electrical power.
Failure to observe these safety precautions could result in personal injury.

«
...
7
8
9
10
11
...
»

Содержание Allen-Bradley MP-Series





































































Отзывы:

Нет отзывов

Похожие инструкции для Allen-Bradley MP-Series

Бренд: MJ Research Страницы: 143

Бренд: Hoval Страницы: 12

Бренд: Cobra Страницы: 15

Бренд: Komatsu Utility Страницы: 32

Бренд: Viessmann Страницы: 14

Бренд: Texas Equipment Страницы: 25

Nanomotion SE Series

Бренд: Johnson Electric Страницы: 33

Бренд: Texas Equipment Страницы: 38

Бренд: Texas Equipment Страницы: 57

Бренд: Texas Equipment Страницы: 60

Para-RC Cloud 0.5 ARF

Бренд: Hacker Страницы: 6

Бренд: Hacker Страницы: 8

Бренд: Hacker Страницы: 8

Бренд: YS Страницы: 2

Бренд: Yanmar Страницы: 248

Бренд: Yanmar Страницы: 317

Бренд: Yanmar Страницы: 308

Бренд: HELIX Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды