Rockwell Automation Allen-Bradley MP-Series Скачать руководство пользователя | Manualshive

Страница: 14 / 68

background image

14

MP-Series Heavy Duty Electric Cylinders

Rockwell Automation Publication MPAI-IN001E-EN-P - March 2012

Verify Connector O-ring and Backshell Seal

An O-ring on the feedback connector, and a backshell seal on the feedback and power/brake

connectors are necessary to achieve the maximum environmental rating. Verify the seal and

O-rings are installed as described.

Attach Motor Cables

Use this procedure to attach the power and feedback cables after the electric cylinder is mounted.

1.

Carefully align each cable connector with the respective motor connector as shown in

the diagram.

2.

Fully seat the feedback connector and the power/brake connector.

•

Hand tighten the collar of a threaded (M4) connector five or six turns.

Location

Verify

•

An O-ring is mounted on the external surface of the
feedback connector and the power/brake connector.

•

The O-ring is undamaged, not twisted, and rests in the
groove near the rear of the connector.

•

A backshell seal covers the joint inside the feedback and
power/brake housings. It seals the joint between the
backshell and the housing of the connector.

•

The backshell seal is undamaged, and it is fully seated
against the face of the backshell.

ATTENTION:

Keyed connectors must be properly aligned and hand-tightened the

recommended number of turns.
Improper connector alignment is indicated by the need for excessive force to seat
connectors. For example, the need to use tools to fully seat connectors.
Failure to observe these safety precautions could result in damage to equipment.

ATTENTION:

When installing a threaded DIN cable with an M4 designation, an O-ring

must be installed in the groove immediately adjacent to the body of the motor
connector. This O-ring dampens the effects of vibration at the cable-to-motor
connection.
Cables requiring O-rings include 2090-XXNPMF-

xx

S

xx

or 2090-CP

x

M4DF-

xx

AF

xx

power

cables, and 2090-CFBM4DF-CDAF

xx

feedback cable.

Continuous flex cables with a SpeedTec DIN connector have an M7 designation.

O-ring

Groove reserved for
quick-lock plug.

Backshell Seal Inside
Feedback and Power/Brake
Connector Housing

«
...
12
13
14
15
16
...
»

Содержание Allen-Bradley MP-Series





































































Отзывы:

Нет отзывов

Похожие инструкции для Allen-Bradley MP-Series

Бренд: Rato Страницы: 65

Бренд: Vascat Страницы: 60

Бренд: Man Страницы: 92

Бренд: Barrus Страницы: 97

Бренд: Superrollo Страницы: 68

3T-MOTORS 3T45-10E

Бренд: 3T-Components Страницы: 12

3T-MOTORS 3T35-13

Бренд: 3T-Components Страницы: 24

3T-MOTORS 3T35-10SD

Бренд: 3T-Components Страницы: 16

3T-MOTORS 3T35-10R

Бренд: 3T-Components Страницы: 20

Бренд: Lycoming Страницы: 38

Бренд: RAAMDECORATIE Страницы: 45

Бренд: PYD Electrobombas Страницы: 36

2.0-1120 - V1.1

Бренд: MVVS Страницы: 2

Бренд: MVVS Страницы: 6

BLACK DEVIL PRO

Бренд: Cors-Air Страницы: 17

HSK35,40, HSSK50

Бренд: Tecumseh Страницы: 8

Бренд: LinMot Страницы: 54

Бренд: LinMot Страницы: 79

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды