Rockwell Automation Allen-Bradley MP-Series Скачать руководство пользователя

Страница: 65 / 68

MP-Series Heavy Duty Electric Cylinders

Rockwell Automation Publication MPAI-IN001E-EN-P - March 2012

Environmental Specifications

Brake Specifications

Attribute

Value

Temperature, operating ambient

0…40 °C (32…104 °F)

Temperature, storage ambient

-25…60 °C (-13…140 °F)

Humidity, relative (noncondensing)

5…95%

Liquid/dust protection

IP67 - dust tight, effects of immersion

(2)

(2) The use of environmentally sealed (Bulletin 2090) cables are required to achieve this International Protection (IP) rating for the complete

unit.

Shock, max

20 g peak, 6 ms duration

Vibration, max

(1)

(1) Tested for one hour per Rockwell Automation specification 10000056670. Contact your distributor for a copy of this specification.

2.5 g peak @ 30…2000 Hz

Cat. No.

Static Torque

Coil Current
at 24V DC

Brake Response Time

Engage

(1)

(1) Brake engage time delay with voltage removed and a metal oxide varistor (MOV) used for arc suppression.

Use of a diode array for arc suppression will approximately double (x2) the engage time delay.

Release

(2)

(2) Brake release time delay with voltage applied.

MPAI-A/B2

xxxx

1.6 N•m (14.0 lb•in)

0.35 A

peak

75 ms

20 ms

MPAI-A/B3

xxxx

M34

4.0 N•m (35.4 lb•in)

0.43 A

peak

40 ms

50 ms

MPAI-A/B4

xxxx

M34

10.0 N•m (88.5 lb•in)

0.67 A

peak

25 ms

35 ms

MPAI-A/B5

xxxx

M34

16.4 N•m (145 lb•in)

0.66 A

peak

15 ms

25 ms

Cat. No.

Estimated Brake Holding Force

MPAI-A/B

xxxx

xxx

(1)

N (lb)

(1) MPAI-A/B

xxxx

xxx

and MPAI-A/B

xxxx

xxx

have ball screw actuators of 5 mm and 10 mm respectively.

MPAI-A/B

xxxx

xxx

(1)

N (lb)

MPAI-A/B

xxxx

xxx

(2)

N (lb)

(2) MPAI-A/B

xxxx

xxx

and MPAI-A/B

xxxx

xxx

have roller screw actuators of 5 mm and 10 mm respectively.

MPAI-A/B

xxxx

xxx

(2)

N (lb)

MPAI-A/B2

xxxx

V34

2300 (517)

N/A

MPAI-A/B3

xxxx

M34

5818 (1308)

2909 (654)

6423 (1444)

3211 (722)

MPAI-A/B4

xxxx

M34

14550 (3271)

7272 (1635)

16062 (3611)

8029 (1805)

MPAI-A/B5

xxxx

M34

23838 (5359)

11921 (2680)

N/A

Содержание Allen-Bradley MP-Series





































































Результаты поиска

Содержание Allen-Bradley MP-Series

Отзывы:

Похожие инструкции для Allen-Bradley MP-Series

Бренды по названию

Популярные бренды

Rockwell Automation Allen-Bradley MP-Series, Руководство по установке

Результаты поиска

Содержание Allen-Bradley MP-Series

Отзывы:

Похожие инструкции для Allen-Bradley MP-Series

Бренды по названию

Популярные бренды