Rockwell Automation Allen-Bradley MP-Series Скачать руководство пользователя | Manualshive

Страница: 40 / 68

background image

40

MP-Series Heavy Duty Electric Cylinders

Rockwell Automation Publication MPAI-IN001E-EN-P - March 2012

Configure Your Servo Drive with Ultraware Software

These steps assume an electric cylinder and Ultra3000 drive are installed and wired as one axis of

a motion system.
For help using Ultraware software as it applies to setting up your electric cylinder, refer to

Additional Resources

. This procedure assumes you are familiar with Ultraware

software.

1.

Connect a serial cable, catalog number 2090-DAPC-D09

xx

, to the CN3 connector on

your Ultra3000 drive.

2.

Apply AC input power to the Ultra3000 drive.
When communication with the Ultra3000 drive is established, the Ultra3000 motor

database dialog box opens.

3.

Click Cancel.
Ultraware software begins scanning for online drives. When a drive is found, an Online

Drive icon opens in the Workspace.

4.

Double-click the Online Drive icon to view the main Drive setup dialog box.

5.

Verify the data in the Model Field is correct for your electric cylinder.

6.

From the Displayed Units pull-down menu, choose User.
This programs Ultraware software to make distance moves in User Units (mm or in.).

«
...
38
39
40
41
42
...
»

Содержание Allen-Bradley MP-Series





































































Отзывы:

Нет отзывов

Похожие инструкции для Allen-Bradley MP-Series

Бренд: BAFANG Страницы: 6

Pad-Mounted Series

Бренд: S&C Страницы: 15

Бренд: Festo Страницы: 76

Бренд: Exalto Страницы: 28

Calzoni MR Series

Бренд: Parker Страницы: 50

Бренд: Deutz Страницы: 37

Бренд: CHERUBINI Страницы: 24

Бренд: Pentair Страницы: 110

Бренд: Tanaka Страницы: 7

Бренд: Mafell Страницы: 166

Бренд: Lombardini Страницы: 57

Бренд: Lombardini Страницы: 94

Бренд: Detroit Diesel Страницы: 116

Бренд: Detroit Diesel Страницы: 158

Бренд: Detroit Diesel Страницы: 172

ZA top SM225.40B

Бренд: ZIEHL-ABEGG Страницы: 76

Бренд: DANA Страницы: 3

Бренд: Teknik Страницы: 121

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды