manualshive.com logo in svg

Rockwell Automation Allen-Bradley Kinetix MMA-B080 Series, Руководство по установке

Поделиться
Скачать
Rockwell Automation Allen-Bradley Kinetix MMA-B080 Series Скачать руководство пользователя страница 44

44

Rockwell Automation Publication MM-IN001B-EN-P - February 2022

Kinetix MMA Asynchronous Main Motors Installation Instructions

Standard maintenance and inspection for the motor includes: 

Feedback Cable and Motor Feedback Connector: Replacement or Rotation

Feedback connectors are not provided as a replacement part from Rockwell Automation, and it is not recommended to remove or replace them. If the upper shell is 
damaged, it can be sourced separately (as an Intercontec M23) and replaced without tampering the feedback wiring and pinout connections. 

A feedback connector replacement is also available when the full Encoder Replacement Kit is requested. 
See the Knowledgebase article: 

Kinetix MMA Frequently Asked Questions

, for additional information.

The motors have an encoder that is connected through a direct coupling. See 

Table 5 on page 14

 for motor 

feedback and pin out information.

Rotate Feedback Connector to a New Position

1.

Connect the feedback cable to the motor feedback connector. 
The attached cable connection provides a larger area to gain more leverage. 

2.

Slowly rotate the motor connector into the desired position. 

3.

Disconnect the feedback cable after the motor feedback connector is aligned.

Remove and Install the Feedback Connector

1.

Remove screws that secure the feedback connector to the motor.

2.

Rotate the feedback connector to the necessary position.

3.

Install the feedback connector on the motor. Torque screws to 1.1 N•m (9.74 lb•in).
Verify that no wires were damaged. 

4.

Follow 

Rotate Feedback Connector to a New Position

 if additional adjustments must be made.

•

Rotate Feedback Connector to a New Position

•

Remove and Install the Feedback Connector

•

Brake Considerations

•

Bearing Inspection and Lubrication

 

•

Brush for Shaft Currents

•

Shaft Key Removal and Installation

•

Replace, Inspect, and Maintain Blower Filters

•

Blower Conversions

•

Instructions to Reposition or Replace the Radial Blower Assembly

•

Install the IC17 Clean-air Kit (Includes: Replace Axial Blower)

•

Replace Extension Rods

•

Replace Encoder

•

Shaft Seals

BURN HAZARD: 

Outer surfaces of the motor can reach high temperatures during motor operation. Take 

precautions to help prevent accidental contact with hot surfaces. Consider motor surface temperature when you 
select motor connectors and cables. Failure to observe these safety procedures could result in personal injury or 
damage to equipment.

ATTENTION: 

Do not conduct the high-voltage test on the encoder terminal. Always use 

shielded cables for the connection with the inverter. To avoid an electric shock hazard, 
verify that the voltage has discharged completely before servicing.

IMPORTANT

The MMA-B080

xxx

 motor does not allow for rotation of the feedback connector. 

For information to change the orientation of the MMA-B080

xxx

, see 

Remove and 

Install the Feedback Connector

.

WARNING: 

Risk of equipment damage. When repositioning the feedback connector, take 

extra caution not to disconnect the wiring, or to bend, twist, or crimp the wires. 

IMPORTANT

The MMA-B080

xxx

 motor does not allow for rotation of the feedback connector.

Feedback connectors are designed with 330° of rotational 
positioning, but this range may be partially or greatly reduced 
because of the blower or motor and blower terminal boxes.

Содержание Allen-Bradley Kinetix MMA-B080 Series





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды