manualshive.com logo in svg

Rockwell Automation Allen-Bradley Kinetix MMA-B080 Series, Руководство по установке

Поделиться
Скачать
Rockwell Automation Allen-Bradley Kinetix MMA-B080 Series Скачать руководство пользователя страница 51

Rockwell Automation Publication MM-IN001B-EN-P - February 2022

51

Kinetix MMA Asynchronous Main Motors Installation Instructions

Instructions to Reposition or Replace the Radial Blower Assembly

Perform this procedure on a workbench. Follow steps for all shaft heights unless otherwise indicated.

1.

Remove incoming power from the motor and the blower. Allow time for any stored energy to discharge.

2.

Use shims or riser blocks to allow clearance for lifting straps, then place the motor on a workbench or other suitable work surface.

3.

Remove the four sets of hardware (nut, screw, spring washer, and/or washer) that secure the blower to the motor. See 

Table 53 on page 52

 for additional 

information. Keep the hardware for 

step 14

.

4.

Attach a crane or other lifting assistant to the blower assembly.

5.

Disconnect 

and remove the four screws that secure the feedback connector to the adapter plate. 

See 

Remove and Install the Feedback Connector

 for additional information.

• For shaft height 180 and 225 only, remove the four screws that secure the adapter plate to the 

blower housing, then slide the feedback connector and wires through the opening and into 
the blower housing.

6.

Slide the blower assembly out approximately 8 cm (3 in.).

7.

Disconnect the feedback connector ground wire inside of the blower housing.

8.

Slide the blower assembly away from the motor and off the extension rods.

9.

Lift, rotate, and move the blower assembly into the new orientation.

ATTENTION: 

For blower weight, see 

Table 7 on page 16

. It is recommended to use two people or a crane to remove 

the blower assembly from the motor. Blower weight exceeds 22.67 kg (50 lbs) in all cases. 

If using the crane for 

assistance, exercise caution and diligence: do not to bend, twist, or strain the extension rods.

IMPORTANT

Secure the feedback cables and ground wire during this procedure to avoid 
damage.

ATTENTION: 

The blower motor is not balanced when lifted. Take precautions 

to avoid swinging, personal injury, or equipment damage. See also 

step 4

.

ATTENTION: 

The blower screws cause a height differential between the 

motor and a repositioned blower. When repositioning the blower to the left or 
right, you may need to add a shim under the motor and level it.

Radial Blower (standard)

Radial Blower with Alternate Orientations

Left

Right

Top

ATTENTION: 

The blower screws 

cause a height differential between 
the motor and a repositioned blower. 
When repositioning the blower to the 
left or right, you may need to add a 
shim under the motor and level it. 

IMPORTANT

See 

Instructions to Lift on page 15

 for 

additional information on blower assembly 
weight. 

Do not lift the blower assembly during this 
step - it may be necessary to adjust the 
tension on the extension rods to slide the 
blower assembly away from the motor. See 

step 8

.

α < 30°

α 

α 

step 3

step 4

Shaft Height
180 and 225 
only

Shaft Height
100, 132, and 160

only

step 5

Figure 19 - Feedback Connector and Ground Location

Содержание Allen-Bradley Kinetix MMA-B080 Series





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды