manualshive.com logo in svg

Rockwell Automation Allen-Bradley Kinetix MMA-B080 Series, Руководство по установке

Поделиться
Скачать
Rockwell Automation Allen-Bradley Kinetix MMA-B080 Series Скачать руководство пользователя страница 46

46

Rockwell Automation Publication MM-IN001B-EN-P - February 2022

Kinetix MMA Asynchronous Main Motors Installation Instructions

Lubrication Procedures 

Where applicable, the motor design has a positive lubrication system for routing new grease directly into the bearing. Follow these steps to lubricate the motor: 

1.

Locate the grease fitting on the motor and/or in the side access panel. 

2.

Remove the grease drain plug opposite the grease inlet. 

Figure 16 - Grease Port Locations

3.

Use a manual grease gun to pump in the recommended amount of grease. 

4.

Replace any temporary grease fittings that were installed, and then wipe away any excess grease. 

5.

Reattach the grease drain plug.

6.

Attach the rear access panels that were removed. See 

Table 45

 for torque values.

Brush for Shaft Currents

Some motors are equipped with a shaft grounding brush (bearings option) or Aegis rings (special option). Their purpose is to close the electric circuit existing between the 
rotor and the motor structure, which allows the shaft voltage discharge currents to pass through the brush and not the bearings. Normally, the brush is installed on the non-
drive end (NDE) side of the motor. A periodic check should take place every 8000 working hours. Replace the brush when there is approximately 5 mm (0.2 in.) of conductive 
carbon brush remaining.

Table 44 - Type of Grease for High Speed Ball Bearings

Manufacturer

Type

Composition

Color

SKF

LGHP2

Mineral di-urea

Blue

Lubcon

Thermoplex 2 TML

Mineral with lithium

Cream

Kluber

Isoflex LDS 18 Special A

Mineral with lithium

Yellow

ATTENTION: 

It is recommended to perform lubrication procedures with a warm motor and stationary shaft. 

Failure to observe these precautions could result in personal injury.

Brush size specifications for replacement: 5 x 8 x 20 mm (0.2 x 0.31 x 0.79 in.)

ATTENTION: 

 This level of service must be done at an authorized Rockwell Automation Service Center.

Front Grease Fitting 

Rear Grease Fitting

Table 45 - Rear Access Panel Torque Specifications

Motor Cat. No.

Screw Type

Torque 

N•m (lb•in)

MMA-B080

xxx

M4

2.5 (22.13)

MMA-B100

xxx

MMA-B132

xxx

M5

4.0 (35.40)

MMA-B160

xxx

MMA-B180

xxx

MMA-B225

xxx

M6

6.0 (53.10)

Содержание Allen-Bradley Kinetix MMA-B080 Series





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды