2
Rockwell Automation Publication 440R-IN089A-EN-P - July 2022
Minotaur MSR142RTP Monitoring Safety Relay Installation Instructions
Diagnostics
The solid-state status signal Y35 indicates the safety input state. The solid-state
status output Y32 and the auxiliary (N.C.) output 41-42 signals the safety output
state.
Safety Input
One safety device can be monitored per unit. According to the wiring inputs,
cross-loop monitoring of the inputs is enabled or disabled. You can enable
cross-loop monitoring for 2-channel safety inputs in 4-wire connection (S11-S12,
S21-S22). Cross-loop monitoring is disabled for single-channel inputs, dual-channel
inputs in 3-wire connection, and 24V DC signals. For external 24V DC signals, the
negative pole must connect to S21.
Reset
•
Reset modes - The reset mode is configurable for automatic/manual start
and manual monitored reset (MSR
xxx
RT).
A valid start/reset can only operate if the feedback circuit is closed.
Feedback contacts (N.C.) of controlled actuators connect to Y1-Y2.
•
T - Automatic/manual start
(a)
In Automatic/Manual Start mode, the reset circuit S33-S34 is not
monitored against signal changes (no edge detection). The safety relay is
active once the safety inputs and the reset circuit close. If the safety
inputs and reset circuit concurrently close during power-up, the safety
relay activates immediately.
•
R - Manual monitored reset
(b)
In Manual Monitored Reset mode, a signal change of the reset circuit
(S33-S34) is required and monitored. A reset fault occurs if the safety
inputs remain open while the reset circuit is closed.
-
Positive edge:
The safety relay is active once the safety inputs close and then the
reset circuit is closed.
-
Negative edge (440R-
xxxxx
M):
The safety relay is active once the safety inputs close and then the
reset circuit closes and releases again. The circuit resets upon release
of the Reset button.
For both methods, the MSR142RTP safety relay is suitable for the safety
requirements according to EN/ISO 13849-1.
Response time
15 ms
Recovery time
100 ms
Impulse withstand voltage
2500V (external wiring according to rated voltage)
Pollution degree
2
Installation group
Overvoltage category III, VDE 0110-1
Operating temperature
-5…+55 °C (23…131 °F)
Relative Humidity
90%
Enclosure protection
IP40 (NEMA 1)
Terminal protection
IP20
Wiring
Use copper that withstands 60/75 °C (140/167 °F)
Conductor size
0.2...2.5 mm
2
(24…12 AWG)
Torque settings
Terminal screws: 0.6…0.8 N•m (5…7 lb•in)
Case material
Polyamide PA 6.6
Mounting
35 mm (1.38 in.) DIN rail in enclosure to a minimum of IP54
Weight
24V AC/DC: 470 g (1.04 lb)
115V AC or 230V AC: 607 g (1.34 lb)
Vibration
10…55 Hz, 0.35 mm (0.01 in.)
(1)
Operation time (day, hour)
(2)
Cycle time (hour, sec)
Max PLc: 1-CH
(1)
; N.C.
(1)
1-CH = Single-channel
Max PLd: 2-CH
(2)
; 3-wire connection
; 24V DC signal
; 4-wire connection, cross
faults require fault reset
Table 1 - Technical Specifications (Continued)
Attribute
Value
(2)
2-CH = Dual-channel
(a)
T = Jumper X1-X2, X3-X4
(b)
R = No jumper
X3
X1
Y1
X4
X2
Y2 S34
S33
K2
K1
S12
S11
X3
X1
Y1
X4
X2
Y2 S34
S33
K2
K1
S12
S11
MSR
xxx
T
MSR
xxx
T
440R-
xxxxx
M
S12
X3
X1
Y1
X4
X2
Y2 S34
S33
K2
K1
S11
S12
X3
X1
Y1
X4
X2
Y2 S34
S33
K2
K1
S11
MSR
xxx
R
MSR
xxx
R
440R-
xxxxx
M
MSR
xxx
R
440R-
xxxxx
M
