Rockwell Automation 1734-OV2E Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 28

background image

22

POINT I/O Protected Sink Output Module

Publication

1734-IN585C-EN-E - December 2005

Indication

Probable Cause

Recommended Action

Network Status

Off

Device is not online.
- Device has not completed
dup_MAC_id test.
- Device not powered - check module
status indicator.

Apply power to the device,
wait for MAC-id to
complete, and correct, if
needed.

Flashing Green

Device is online but has no
connections in the established state.

None - device is in Idle or
Program mode.

Solid Green

Device is online and has connections
in the established state.

None

Flashing Red

One or more I/O connections are in
timed-out state.

Check for I/O module
failure, and correct, as
needed.

Solid Red

Critical link failure - failed
communication device is present.
Device detected error that prevents it
communicating on the network.

1. Reinstall adapter and
terminal base, if
improperly installed.
2. Correct duplicate
MAC_id, if needed.

Flashing Red/Green

Communication faulted device - the
device has detected a network access
error and is in communication faulted
state. Device has received and
accepted an Identify Communication
Faulted Request - long protocol
message.

Verify that adapter is
properly installed, and
reinstall, as needed.

I/O Status

Off

All outputs are inactive.

None

Solid Yellow

One or more outputs are active and
under control.

None

Solid Red

Overload, short circuit, or
overtemperature detected (On-State
only).

Remove overload, short
circuit, or overtemperature
condition.

«
...
20
21
22
23
24
...
»

Содержание 1734-OV2E





























Отзывы:

Нет отзывов

Похожие инструкции для 1734-OV2E

Бренд: b-red Страницы: 7

Бренд: Habegger Страницы: 2

Бренд: S&S Northern Страницы: 9

Бренд: texet Страницы: 28

Бренд: V-Tec Страницы: 2

Бренд: hotset Страницы: 2

Бренд: Niko Страницы: 104

Бренд: Start Shaphon Страницы: 66

Бренд: Danfoss Страницы: 8

Бренд: American Panel Страницы: 18

Aureon 7.1 FireWire

Бренд: TerraTec Страницы: 2

Бренд: Velux Страницы: 24

Бренд: AccessPRO Страницы: 8

PORTA GANTRY 1100

Бренд: REID LIFTING Страницы: 28

Бренд: Bishamon Страницы: 19

Бренд: Powrmatic Страницы: 36

Бренд: Korg Страницы: 6

Бренд: babala Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды