Rocks OK-03.4130, Руководство пользователя

Страница: 78 / 106

78
TROUBLE SHOOTING / DIAGNOZOWANIE I USUWANIE USTEREK / FEHLERERKENNUNG UND -BEHE-
BUNG / HIBAELHÁRÍTÁS / DIAGNOSTIKA A ODSTRAŇOVÁNÍ PORUCH /
DIAGNOSTIKA A ODSTRAŇOVANIE PORÚCH
8
Problem Alert info Possible reasons Solutions
Auto mode is not able to
start,charging station is
beeping.
Virtual wire was cut off. The virtual wire was cut off.
1.Check the virtual wire light on char-
ging station. Be sure the virtual wire is
connected to the charging station well
(light in colorless).
2. Connect the virtual wire with wire
connectors.
Auto mode is not able to
start,charging station is
beeping.
Signal light is off.
Charging station is out of power.
1.main power is shut off. Bad
communication between char-
ging station and mower.
1. Check the power and make sure the
charger is connecting well with power
supply and charging station.
Mower stops working and
beeps.
Wire signal is lost, pls check. The virtual wire fails to send
signals.
Pls test the wire sensors on the area
where the mower lost signals, if the
signals is too weak, pls re-set the
virtual wire
Mower stops working and
beeps.
Lift sensor or pressure sensor
activated.
1. Mower is lifted from ground.
2. Someone or object ride or sit
on the mower.
1. Take the mower to level ground and
restart it.
2. Take the object away from mower
and restart it.
Mower stops working and
beeps.
Current of right running mo-
tor is too large,check it.
Current of left running motor
is too large,check it.
1. Running wheel strike hard
objects.
2. The mower is trapped in
lawn.
1. Clean the lawn and make sure it is
free from hard objects.
2. Clean the lawn where mower is trap-
ped or restart the mower in another
place.
Mower stops working and
beeps.
Mower is got stuck, pls check
1. Blade protective shield is
blocked.
2. Mower is got stuck
1. Clean the blade protective shield and
restart the mower.
2. Take out the mower manually and
restart the mower
Mower stops working and
beeps.
Mower runs out of wire, pls
check
Mower runs out of virtual wire Virtual wire signal is too weak. Pls set
the virtual wire current to an appropria-
te value or re-set the virtual wire where
is with weak signal.
Mower stops working and
beeps.
Current of cutting motor is
too large,check it.
1.Cutting height is too low.
2. Blade strikes hard objects.
3. Mower is trapped in lawn
1. Adjust the cutting height to suitable
height.
2. Clean the lawn and make sure it is
free from hard objects.
3. Clean the lawn where mower is trap-
ped or restart the mower in another
place.
Mower stops working and
beeps.
Robot is over tilted. Mower is tilted over than 30
degrees from the ground.
Turn off the mower and take the
mower to level ground. Then re-
start the mower.
The batteries can not
recharge
1.Charger is not powered on.
2.Battery lifetime decreases.
1. Check whether charger is well con-
nected.
2. Send the mower to service station
and replace the battery.
Mower gets stuck, does
not move.
1. Grass is extremely overgrown
or very wet,
2. Terrain needs landscaping
repairs.
1. Cut the grass appropriate height.
2. Fill in all holes, cover or exclude all
exposed roots in order to smooth the
terrain.
Mower does not comple-
te the edge.
Obstacle along the path. Watch the full operation of follow virtu-
al wire walking and confirm no obstacle
is present.
EN