manualshive.com logo in svg

Rock Shox BoXXer R2C2, Техническое руководство

Поделиться
Скачать
Rock Shox BoXXer R2C2 Скачать руководство пользователя страница 11

GEN.0000000003185 REV A

11

bo

XX

er r2C2 TeChniCal Manual

se al serviCe 

Suspension fork seals are considered "wear and tear" parts and require regular maintenance.  The frequency of seal replacement 

will depend on the frequency of riding, riding terrain, rider body weight, and type of fork.  The following chapter covers wiper and 

oil seal removal and installation.

wiper  &  oil  seal  reMoval

Position the tip of a downhill tire lever or large, 

1. 

flat head screwdriver underneath the lip of the 

lower black oil seal, above the upper bushing. 

Stabilize the lower leg upright on a bench top or 

2. 

on the floor.  Hold the lower leg firmly and use 

downward force on the tool handle to  

leverage both seals out at the same time. 

be sure to stabilize the lower leg in order to 

prevent it from slipping while installing the seal.  

do not allow the lower legs to twist in opposite 

directions, compress toward each other, or be 

pulled apart.  This will damage the lower leg.  

Spray isopropyl alcohol on and into the lower leg.  

3. 

wipe the lower legs clean, then wrap a clean, 

lint free rag around a dowel and clean the inside 

of each lower leg.

wiper  &  oil  seal  insTallaTion

Position the oil seal, with the grooved side  

1. 

visible, onto the stepped side of the 35 mm seal 

installation tool.

Hold one of the lower legs firmly and use the seal 

2. 

installation tool to push the oil seal evenly and 

completely into that leg.  Repeat for the other 

leg. 

be sure to stabilize the lower leg in order to 

prevent it from slipping while installing the seal.  

do not allow the lower legs to twist in opposite 

directions, compress toward each other, or be 

pulled apart.  This will damage the lower leg.  

Position the dust wiper seal, with the grooved 

3. 

side visible, into the recessed side of the 35 mm 

seal installation tool.

Hold one of the lower legs firmly and use the seal 

4. 

installation tool to push the dust wiper evenly 

and completely into that leg.  Repeat for the  

opposite leg.

inTroduCTion

1

2

3

4

1

2

3

Содержание BoXXer R2C2






















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды