Roberts Gorden Blackheat BH15ST, Инструкция по установке, эксплуатации и обслуживанию

Страница: 69 / 84

SECTION 15: S
ERVICING
I
NSTRUCTIONS
63 of 75
15.2.4 Automatic Flame Control Unit
Remo v e black ignition lead. Withdra w the connectors.
Remo v e t w o scre w s from the co v er. Replace if fa u lty.
Refit in re v erse seq u ence.
15.2.5 Pressure Switch
Disconnect the t w o silicone t u bes. Remo v e w ires from
the three blades. Remo v e t w o scre w s w hich sec u re the
press u re s w itch to the b u rner. Remo v e press u re s w itch.
Replace press u re s w itch, if fa u lty, and refit in re v erse
seq u ence ens u ring that the r u bber t u bes are reconnected
to the s w itch correctly.
Note: Wires fitted as follo w s:
NO - Yello w
NC - White
Common - Black
15.2.6 Neons
Remo v e the t w o p u sh on connectors and remo v e the
neons by p u shing do w n w ards. Replace in re v erse
seq u ence.
15.3 Maintenance Checklist
Installation Code and Annual Inspections:
All installation and ser v ice of ROBERTS GORDON
®
eq u ipment m u st be performed by a contractor
q u alified in the installation and ser v ice of eq u ipment
sold and s u pplied by Robert-Gordon E u rope Limited
and conform to all req u irements set forth in the
ROBERTS GORDON
®
man u als and all applicable
go v ernmental a u thorities pertaining to the
installation, ser v ice, operation and labeling of the
eq u ipment. To help facilitate optim u m performance
and safety, Robert-Gordon E u rope Limited
recommends that a q u alified contractor cond u ct, at
a minim u m, ann u al inspections of yo u r ROBERTS
GORDON
®
eq u ipment and perform ser v ice w here
necessary, u sing only replacement parts sold and
s u pplied by Robert-Gordon E u rope Limited.
The Vicinity of the Heater Do not store or u se flammable objects, liq u ids or v apo u rs near the heater.
Immediately remo v e these items if they are present.
See Page 5, Section 3 .
Vehicles and Other
Objects Maintain the clearances to comb u stibles.
Do not hang anything from, or place anything on, the heater.
Make s u re nothing is lodged u nderneath the reflector, in bet w een the t u bes
or in the decorati v e or protecti v e grilles (incl u ded w ith select models).
Immediately remo v e objects in v iolation of the clearances to comb u stibles.
See Page 5, Section 3 .
Reflector S u pport reflector w ith hanger and s u pport strap.
Reflector m u st not to u ch t u be.
Make s u re there is no dirt, sagging, cracking or distortion.
Do not operate if there is sagging, cracking or distortion.
Make s u re reflectors are correctly o v erlapped. See Page 23, Section 6.6.1 .
or Page 34, Section 7.8.1 .
Clean o u tside s u rface w ith a damp cloth.
Vent Pipe Venting m u st be intact. Using a flashlight, look for obstr u ctions, cracks on
the pipe, gaps in the sealed areas or corrosion.
The area m u st be free of dirt and d u st.
Remo v e any carbon deposits or scale u sing a w ire br u sh.
See Page 50, Section 11 .
Outside Air Inlet Inlet m u st be intact. Look for obstr u ctions, cracks on the pipe, gaps in the
sealed areas or corrosion.
The area m u st be free of dirt and d u st. Clean and reinstall as req u ired.