Roberts Gorden Blackheat BH15ST, Инструкция по установке, эксплуатации и обслуживанию

Страница: 10 / 84

B
LACKHEAT
®
I
NSTALLATION
O
PERATION AND
S
ERVICE
M
ANUAL
4 of 75
SECTION 2: INSTALLER RESPONSIBILITY
• To install the heater, as w ell as the gas and electrical
s u pplies, in accordance w ith applicable specifications
and codes. Robert-Gordon E u rope Limited recom-
mends the installer contact a local B u ilding Inspector
or Fire
Marshal for g
u idance.
• To u se the information gi v en in a layo u t dra w ing and
in the man u al together w ith the cited codes and
reg u lations to perform the installation.
• To install the heater in accordance w ith the clear-
ances to comb u stibles.
• To f u rnish all needed materials not f u rnished as
standard eq u ipment.
• To plan location of s u pports.
• To pro v ide access to b u rners for ser v icing on all
sides, for b u rner remo v al.
• To pro v ide the o w ner w ith a copy of this installation,
operation and ser v ice man u al.
• To ne v er u se heater as s u pport for a ladder or other
access eq u ipment and ne v er hang or s u spend any-
thing from heater.
• To ens u re there is adeq u ate air circ u lation aro u nd the
heater and to s u pply air for comb u stion, v entilation
and distrib u tion in accordance w ith local codes.
• To safely and adeq u ately install heater u sing materi-
als w ith a minimal w orking load of 33 kg.
• To ens u re the heater is placed in an appro v ed
application.
2.1 Low Level User Instructions
In all sit u ations, clearances to comb u stibles m u st be
maintained. Signs sho u ld be posted in storage areas to
specify the maxim u m stacking height of items placed
belo w heater to maintain req u ired clearances to
comb u stibles. Minim u m clearances m u st be maintained
from v ehicles parked belo w the heater. Ca u tion sho u ld be
u sed w hen r u nning the system near comb u stible
materials s u ch as w ood, paper, r u bber, etc. Consideration
sho u ld be gi v en to partitions, storage racks, hoists,
b u ilding constr u ction, etc.
A laminated w all tag is a v ailable for the heater as a
permanent reminder of the safety instr u ctions and the
importance of the req u ired clearances to comb u stibles.
Please contact Robert-Gordon E u rope Limited or yo u r
ROBERTS GORDON ® independent distrib u tor to obtain
the w all tag. Affix the tag by peeling off the backing of the
adhesi v e strips on the rear s u rface and position the tag
on a w all near the heater (e.g. thermostat or ROBERTS
GORDON
®
Controller).
A copy of the w all tag (P/N 91037912) is ill u strated on the
back co v er. This copy of the w all tag can be affixed on the
w all near the heater. Kno w yo u r model n u mber and
installed config u ration. Model n u mber and installed
config u ration are fo u nd on the b u rner and in the
Installation, Operation and Ser v ice Man u al. Write the
largest clearance dimensions w ith permanent ink
according to yo u r model n u mber and config u ration in the
open spaces on the tag.
2.2 Corrosive Chemicals
Robert-Gordon E u rope Limited cannot be responsible for
ens u ring that all appropriate safety meas u res are
u ndertaken prior to installation; this is entirely the
responsibility of the installer. It is essential that the
contractor, the s
u b-contractor, or the o w ner identifies the
presence of comb u stible materials, corrosi v e chemicals
or halogenated hydrocarbons* any w here in the premises.
* Halogenated Hydrocarbons are a family of chemical
compounds characterized by the presence of halogen
elements (fluorine, chlorine, bromine, etc.). These com-
pounds are frequently used in refrigerants, cleaning
agents, solvents, etc. If these compounds enter the air
supply of the burner, the lifespan of the heater compo-
nents will be greatly reduced. An outside air supply must
be provided to the burners whenever the presence of
these compounds is suspected. Warranty will be invalid
if the heater is exposed to halogenated hydrocarbons.
2.3 National Standards and Applicable Codes
All appliances m u st be installed in accordance w ith the
latest re v ision of the applicable standards and national
codes. This refers also to the electric, gas and v enting
installation. Note: Additional standards for installations in
p
u blic garages, aircraft hangars, etc. may be applicable.
ALL INSTALLATONS:
These appliances shall be installed by s u itably q u alified
personnel in accordance w ith the req u irements of
AS5601-2010 [or later editon]; this appliance man u al and
any codes or standars w hich may apply to the
application.
EXTERNAL INSTALLATION:
Appliances may be installed in external non-residential
areas s
u ch as patios and u nder ea v es pro v ided
clearances to comb u stibles and minim u m mo u nting
heights are complied w ith and that the appliances are
protected from rain and not s u bject to w ind speeds in
excess of 15 kph. All external applications shall be
appro
v ed for s u itable u se by the appliance man u afact u rer
or their representati v e.
CAUTION
Product Damage Hazard
Do not use heater in area containing
corrosive chemicals.
Refer to appropriate Material Safety Data
Sheets (MSDS).
Failure to follow these instructions can result
in product damage.