Robe ROBIN SilverScan Скачать руководство пользователя страница 34

Страница: 34 / 44

Checking plastic parts of the fixture

The plastic parts of the fixture should be checked for damages and beginning cracks at least every two months.

If hint of a crack is found on some plastic part, do not use the fixture until the damaged part will be replaced.

Cracks or another damages of the plastic parts can be caused by the fixture transportation or manipulation and

also ageing process may influence plastic materials.

This checking is necessary for both fixed installations and preparing fixtures for renting. Any free moving parts

inside of the fixture or any cracked plastic not sitting properly in place need to be immediately replaced.

12.1 Disposing of the product

To preserve the environment please dispose or recycle this product at the end of its life according to the local
regulations and codes.

13. ChangeLog

This section summarizes changes in the user manual.

Version of the

manual

Date of issue

Description of changes

1.1

05/09/2019

SilverScan dimensions changed

1.2

18/09/2019

DMX protocol ver. 1.1 (RoboSpot Support added)

1.3

23/09/2019

Position of the fixture in flight case changed

1.4

14/10/2019

Warning "Risk group 2" added

Содержание ROBIN SilverScan













































Результаты поиска

Содержание ROBIN SilverScan

Отзывы:

Похожие инструкции для ROBIN SilverScan

Бренды по названию

Популярные бренды

Robe ROBIN SilverScan, Руководство пользователя

Результаты поиска

Содержание ROBIN SilverScan

Отзывы:

Похожие инструкции для ROBIN SilverScan

Бренды по названию

Популярные бренды