Robe Robin DL7F, Руководство пользователя

Страница: 28 / 58

28
Bd. Reset 1 M
- a barndoor 1 reset
Bd. Reset 2 M
- a barndoor 2 reset
Bd. Reset 3 M - a barndoor 3 reset
Bd. Reset 4 M - a barndoor 4 reset
Bd. Shutter 1 Move - a movement of the barndoor 1
Bd. Shutter 2 Move - a movement of the barndoor 2
Bd. Shutter 3 Move - a movement of the barndoor 3
Bd. Shutter 4 Move - a movement of the barndoor 4
Calibration of the effects via the control board
1. Disconnect DMX controller from the fixture and enter the "Calibrate Effects" menu.
2. Use the [up arrow] and [down arrow] to find "Pan" and touch it to enter the fine effect adjustment screen.
3. Set desired value and save it by touching the [confirm].
4. Repeat steps 2 and 3 for next item
5. After calibrating all effects, touch the [confirm] to save all adjusted values and reset the fixture.
Calibration of the effects via the DMX controller
1. Connect DMX controller to the fixture and enter the "Calibrate Effects" menu.
Calibration protocol:
Effect Mode 1 Mode 2 Mode 3 Mode 4
Pan channel 35 channel 30 channel 43 channel 34
Tilt channel 36 channel 31 channel 44 channel 35
Frost channel 37 channel 32 channel 45 channel 36
Zoom channel 38 channel 33 channel 46 channel 37
Focus channel 39 channel 34 channel 47 channel 38
Bd. Shutters rot. channel 40 channel 35 channel 48 channel 39
Bd. Reset 1 M channel 41 channel 36 channel 49 channel 40
Bd. Reset 2 M channel 42 channel 37 channel 50 channel 41
Bd. Reset 3 M channel 43 channel 38 channel 51 channel 42
Bd. Reset 4 M channel 44 channel 39 channel 52 channel 43
Bd. Shutter 1 Move channel 45 channel 40 channel 53 channel 44
Bd. Shutter 2 Move channel 46 channel 41 channel 54 channel 45
Bd. Shutter 3 Move channel 47 channel 42 channel 55 channel 46
Bd. Shutter 4 Move channel 48 channel 43 channel 56 channel 47
Calibrate Colours
- The menu serves for calibration of white colours in the factory.
Green Corrections - The menu allows to corrected calibrated whites for CRI 70 and 90.
Opto Corrections - The menu item serves for re-calibration of the light source. The re-calibration takes cca
5 minutes. DO NOT SWITCH OFF THE FIXTURE during this process until the message "Correction done" will
appear.
LEDS HW version - The item serves for selection of right HW version of light source. User
should not change this item.
Calibrate Pan/Tilt EMS - This menu item allows calibration of the pan/tilt electronic motion stabilizer.
Important: during this calibration any external force must not influence the fixture and the surface at which
the fixture stands (or truss if the fixture hangs) has to be without movement, shake, strokes etc.
Load Default Calibrations
- The item loads default (factory) calibration values.
Updating software - The menu item allows you to update software in the fixture via either serial or USB port
of PC.
The following are required in order to update software:
- PC running Windows 95/98/2000/XP/7/8 or Linux
- DMX Software Uploader
- Flash cable RS232/DMX No.13050624 (if you want to use a serial port of PC)
- Robe Universal Interface (if you want to use an USB port of PC)
Note: Software update should execute a qualified person. If you lack qualification, do not attempt the
update yourself and ask for help your ROBE distributor.
DMX address, IP address, programs 1-3 and all items in the menu "Personality" will be set to their default
(factory) values.