Robe Color Spot 1200 AT, Руководство пользователя

Страница: 31 / 43

31
6 Special Functions 22 Gobo 2 F. Indexing
7 Pan/Tilt Macro 23 Effect Wheel
8 P./T. Macro Speed 24 Effect Indexing
9 Colour Wheel 25 Effect F. Index.
10 Cyan 26 Frost
11 Magenta 27 Iris
12 Yellow 28 Zoom
13 Conversion Filter 29 Focus
14 CMY Colour Macro 30 Shutter/Strobe
15 Effect Speed 31 Dimmer
16 Effect Spd Assig. 32 Dimmer Fine
Please refer to the chapter "DMX- protocol" for detail description.
Lamp Presetting --- Select this menu to change the lamp "behaviour".
Lamp On/Power On --- Select this function to turn the lamp on automatically after switching the
fixture on.
Lamp Off via DMX --- Select this function to switch off the lamp via DMX.
Lamp On if DMX Present --- This function allows you to strike the lamp automatically after 26
seconds if DMX signal is present on the data link.If the ignition is unsuccessfull (e.g.lamp is too
hot),the fixture will try to ignite the lamp after next 26 s.This process will repeat until the lamp lights.
Lamp Off if not DMX --- This function allows you to switch Off the lamp automatically after 2
minutes if DMX signal is missing on the data link.
Lamp Light Sensor --- Select this function to switch the lamp light sensor on or off.The option"On" is for the
standard operation.
Important: The option"Off" is for "emergency operation" only if the lamp light sensor is defective and you will wait
for a service intervertion! If the lamp light sensor is switched off and at switching the lamp on the electronics will
still try to ignite the lamp until it shines (even when the lamp is damaged or absent), on this account some
electronics parts could be damaged!
Display Adjusting --- This function allows you to change the display settings.
Display Permanent On --- This function allows you to keep the display on or to turn off automatically
2 minutes after last pressing any button(or a wheel movement) on the control panel.
Display Intensity --- Select this function to adjust the display intensity (1-min.,10-max.).
Display Backlight --- Select this function to adjust the display backlight (1-min.,10-max.).
Display Turned --- Select this function to turn the display by 180°.
Blackout d.M.C. --- Select this function to enable the blackout during the head movement correction (if the
moving head lost its right pan/tilt position for a short moment)
.
Pan/Tilt Feedback --- This function allows to return the mowing head to the required pan/tilt position after changing
the position by external force (e.g.by stroke).
Be careful, the Pan/Tilt Feedback OFF is not the standard operation and the head of the fixture can be
demaged!
Note: If the feedback was switched off ,the pan/tilt-position is changed by an external force and the feedback is
switched on again,the moving head might not to be synchronized with the DMX signal.You have to make a reset
in order to synchronize the moving head with the DMX signal.
Microphone Sensitivity --- Select this function to adjust the microphone sensitivity from 1(maximum) to
20(minimum).If the sensitivity is correctly adjusted,the mark will appear (blinking in the bass beat.)
Fan Modes --- By using this function you can choose 2 types of the fan speed operating modes.
Auto Cooling --- The fans automatically raise their speed in order to control inside temperature
of the lighting, if the temperature inside increases about certain level (the low fan speed reduces the
cooling of the lighting). This cycle can repeat several times until the temperature inside is on a
suitable level.The initial level of the fan speed can´t be adjusted by the DMX.
High Cooling --- The cooling fans work on max. speed (max. cooling).This mode we recommend for
high ambient temperature (30 °C and more).
Pan/Tilt mode --- Use this menu to set the character of the pan/tilt movement.