manualshive.com logo in svg

RITE-HITE Dok-Lok STR-4000, Руководство по установке, Страница: 16 / 20

Поделиться
Скачать
RITE-HITE Dok-Lok STR-4000 Скачать руководство пользователя страница 16

16

Pub. No. 1200 — November 2005

RITE-HITE STR-4000 DOK-LOK Installation Manual

VALVE BLOCK ASSEMBLIES

Lower Port

to STR4

Raise Port

to STR4

WKC (SOL 3)

Leveler Ramp

Block Solenoid

WKV (SOL 2)

Leveler Lip

Block Solenoid

Leveler

Lip Out

Port

WKX (SOL 1)

Directional

Solenoid

WKV (SOL 2)

Leveler Lip

Block Solenoid

WKC (SOL 3)

Leveler Ramp

Block Solenoid

Return to

Tank Port

Leveler

Ramp Out

Port

Adjustable

Relief Valve

NOTE: LOCATED ADJACENT TO LEVELER POWER UNIT.

ONLY ON COMBINATION POWER UNITS.

Figure 15 - Combination Power Unit Valve Block Assembly

Adjustable

Relief Valve

NOTE: MOUNTED ON STR-4000 CARRIAGE.

Raise Support 
Cylinder (Left)

Lower Support 
Cylinder (Left)

Raise Support 
Cylinder (Right)

Lower Support 
Cylinder (Right)

Lower To
Power Unit
or Combo
Valve Block

Pressure To
Power Unit
or Combo
Valve Block

Hook Cylinder
Retract (HL)

Hook Cylinder
Extend (HR)

Figure 14 - Auxillary Manifold

Содержание Dok-Lok STR-4000





















Отзывы:

Нет отзывов