Rise HY.CELL Скачать руководство пользователя страница 6

11

CONTROL PANEL HY.CELL

WIRE DIAGRAM

Control panel for 1 hydraulic bollard HYDRA serie.

Terminals

Function

Description

L-N-GND

Power supply

Input, 230VAC 50Hz (HY.CELL)
Input, 115VAC 50/60Hz (HY.CELL 115V))
(1-Phase/2-Neutral/GND-Ground connection)

1-2-3

Motor

Connection to the motor: 
(1-lowering/2-common /3-raising)

6

Inf

Connection bollard status 

DOWN

DOWN

Lowering command input  (N.O. contact.), 
programmable as clock contact

UP

UP

Raising command input  (N.O. contact)

PHOT

PHOT

Safety devices input , N.C. contact (photocells, loop detectors ).

STOP

STOP

Input, STOP key (N.C. contact)

COM

COM

Common, all control inputs.

P.P.

Step-by-Step

Input, step-by-step key (N.O. contact).
In “Service man” mode, it activates the DOWN control function. 

24 VAC

24Vac

Output, 24Vac/200mA max accessory power supply. 

SCA

SCA/SYREN

Not insulated  potential clean contact for the connection of a war-
ning light or an acoustic device.
See also DIP 4 functions

SHIELD-ANT

Antenna

Connection of the antenna to the incorporated radio-receiver module 
(SHIELD-screen/ANT-signal). 

Note: 

The control unit uses a “P2” key with the same functions of the Step-by-Step push-button. This is useful 
to control the automatic system during installation (only with DIP2: OFF).

TRIMMER FUNCTIONS

TW

  

It allows the maximum duration of raising and lowering.

 

It must be preset approx. 4s more with respect to the actual stroke time of the system.

 

The adjustment ranges from 

6s 

to 

18s

 maximum.

TCA

  

If activated , by meand of DIP 1, it allows to adjust a delay time for the automatic raising of the 
bollard . 

 

The adjustment ranges from 3s to 90s maximum.

12

DIP-SWITCH FUNCTION

Dip-Switches Function

Description

DIP1

TCA

Enable or disable the automatic raising of the bollard. The delay time 
can be set by trimmer TCA.
On: Enable automatic raising
Off: disable automatic raising

DIP2

Preflashing

Enable or disable the lights of the bollard

DIP3

Fast automatic 
raising

Enable or disable  the fast automatic raising  of the bollard  (DIP1 
must be  ON).
On: Fast automatic raising activated . When the bollard is in lower 
position , the intervention of the photocell causes the raising of the 
bollard after 3 sec. If the intervention happens  during the lowering 
cycle of the bollard, the lowering cycle will be completed and after 3 
sec. the bollard will do the raising cycle.
Off: Fast automatic raising not activated.

DIP4

SCA/SYREN

Select the operation mode of the output SCA/SYREN.
On: Warning acustic device, is activated during the raising cycle .
Off: Warinig light, it indicates the status of the bollard:
- Light on  = bollard UP
- Fast flashing during raising cycle
- Slow flashing during lowering cycle 
- Light off= bollard down 

DIP5

Block keeping 

See hereunder the paragraph “block keeping”

DIP6

Not used 

RE-PRESSURISEING OF HYDRAULIC LOCKING

The re-pressuriseing of hydraulic locking function keeps the bollard in a stable UP position also when it 
remains UP for long time.
This is a selectable function , it makes the bollard to do a short raising cycle  that assure the correct UP 
position of the bollard. The time intervals of the short raising cycles can be selected . 
In order to activate this function it is necessary to put the DIP 5 in ON position. The green led light indicates 
the time interval between the short raising cycles. The time interval can be selected by means of the push 
button P1, hereunder you can see how to select the different time interval:

1 flash with pause

30 minutes

2 flashes with pause 

1 hour (default)

3 flashes with pause

1 hour and 30 minutes

4 flashes with pause 

2 hours

5 flashes with pause  

2 hours and 30 minutes

6 flashes with pause

3 hours

7 flashes with pause 

3 hours and 30 minutes 

8 flashes with pause 

4 hours

9 flashes with pause 

4 hours and 30 minutes

10 flashes with pause 

5 hours

11 flashes with pause 

5 hours and 30 minutes

12 flashes with pause 

6 hours

LED fixed ON 

Deactivated  function

After choosing the time interval put the DIP 5 in OFF position to confirm your selection.

Содержание HY.CELL













Отзывы: