Rinnai RS100 Скачать руководство пользователя страница 28

Страница: 28 / 41

www.rinnai.us

• Some DHW parameters are accessible but should never be adjusted. This is indicated with N/A at the

description. Ensure factory settings are always maintained at these parameters

• DHW parameters that are available at the user level are indicated below
• This chapter is not available on combi boilers or if there is no sensor at terminals 16 and 17 (DHW priority)

PARA

Description

Range / Explanation

Factory

Setting

User

Access

DHW economy

(nighttime

setback) temp

°F to DHW

max temp
(PARA 6)

Temp for DHW during night time
setback.

100

°F

Yes

NOTE: 100

°F=Default at shipment, 68°F=Default at System Reset

DHW Legionella

Protection

OFF

No Legionella protection

Monday

Yes

Mo-Su, ALL

One day only or every day (ALL)

DHW Legionella

time of operation

0:00 to 23:00

This is not available if PARA 2 is
OFF

2:00

(am)

DHW Legionella

operation temp

°F to DHW

max temp
(PARA 6)

This is not available if PARA 2 is
OFF. Do not adjust lower than
140

°F

149

°F

N/A

This should not be altered

131

°F

Yes

DHW Parameters

DHW max temp

°F to 176°F

This overrides boiler PARA 31.

149

°F

NOTE: This value will go to 203

°F but the boiler will never eclipse 176°F; NOTE: During a split load between

heat and DHW, the supply temp is based on DHW needs

—do not use on direct-coupled in-floor radiant systems

Содержание RS100










































Результаты поиска

Содержание RS100

Отзывы:

Похожие инструкции для RS100

Бренды по названию

Популярные бренды

Rinnai RS100, Тренировочная программа

Результаты поиска

Содержание RS100

Отзывы:

Похожие инструкции для RS100

Бренды по названию

Популярные бренды