Rinnai REU-VR2426WS Solar 26 Скачать руководство пользователя страница 8

Страница: 8 / 53

REU-VR2626WB (B26) /REU-VR2426WS (S26) /REU-VRM2626WG (INF26)

- 5 -

Issue 3 - 13/11/14 ©Rinnai

Sensors and Safety Functions

•

Hot Water Delivery Thermistor

: Measures hot water temperature at the outlet valve (i.e. the ‘mixed’

temperature).

•

Flame Rod

: Monitors combustion characteristics inside the combustion chamber. If the flame fails,

gas supply is stopped.

•

Overheat Switch

: Situated on the heat exchanger, gas supply is stopped when water temperature

reaches 97ºC for a number of seconds.

•

Fusible Link

: Situated on the heat exchanger, electrical power supply is stopped if the temperature

exceeds 129ºC.

•

Water Pressure Relief Valve:

Safeguards the water circuit against excessive inlet pressure. Opens at

2060 kPa, closes at 1470 kPa.

•

Electrical Fuse:

(3A glass fuse) prevents against power surges.

•

Surge Protector:

prevents against over-current.

•

Boil Dry Prevention:

If water flow sensor detects no flow, gas supply is stopped.

•

Combustion Fan Speed Sensor

: In case of combustion fan defect (no rotation of fan blades) gas

supply is stopped.

•

Temperature Cutout:

If the delivered hot water temperature rises above the required delivery

temperature for a number of seconds, the gas supply is stopped.

Combustion Specifications

Refer to dataplate on appliance.

Содержание REU-VR2426WS Solar 26






















































Результаты поиска

Содержание REU-VR2426WS Solar 26

Отзывы:

Бренды по названию

Популярные бренды

Rinnai REU-VR2426WS Solar 26, Руководство по обслуживанию

Результаты поиска

Содержание REU-VR2426WS Solar 26

Отзывы:

Бренды по названию

Популярные бренды