manualshive.com logo in svg

Rinnai REU-VR2426WS Solar 26, Руководство по обслуживанию

Поделиться
Скачать
Rinnai REU-VR2426WS Solar 26 Скачать руководство пользователя страница 31

REU-VR2626WB (B26) /REU-VR2426WS (S26) /REU-VRM2626WG (INF26)

- 27 -

Issue 3 - 13/11/14 ©Rinnai

To return to normal operation

• 

Press the ON/OFF button again while holding down the Water Temperature "DOWN" (Cooler)

button.

To return to normal operation

• 

Press the ON/OFF button again while holding the Water Temperature “UP” (Hotter) button.

• 

This feature will automatically shut down after 3 minutes.

16.  Gas Pressure Setting Procedure

Refer seperate Rinnai document behind front cover of appliance.

17.  Gas Conversion Procedure

Refer seperate document available from Rinnai.

Error History 

To Display Error Memory (History)
(This feature will show the last 10 faults in sequence)
 
1.

Turn off at the ON/OFF button. (This can be done during 
operation)

2.

Press the ON/OFF button while holding the Water Temperature 
"UP" (Hotter) button.

•

 The Sequence will be shown in the Water Temperature display. 

• 

Error Code will be shown in the Clock display. (See service 

Manual for error codes).

•

 Where there are less than a total of 9 errors, "FFF" or " - - " will 

be displayed in the Clock display.

Содержание REU-VR2426WS Solar 26






















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды