manualshive.com logo in svg

Rinnai REU-VR2426WS Solar 26, Руководство по обслуживанию

Поделиться
Скачать
Rinnai REU-VR2426WS Solar 26 Скачать руководство пользователя страница 22

REU-VR2626WB (B26) /REU-VR2426WS (S26) /REU-VRM2626WG (INF26)

- 19 -

Issue 3 - 13/11/14 ©Rinnai

13.  Fault Finding

If there is a fault with the appliance, and controllers are installed, a numerical fault code may appear on the
digital display controller. If controllers are not installed, one may be fitted to find out the fault code. Fault
finding without controllers (and thus fault codes) is possible but more time consuming.

To diagnose and rectify faults, the 

Fault Finding Table

 is used as illustrated below:

Fault Finding Table

Describes possible faults 

and error codes. 

(page 20)

Operational 

Flow Chart

 

(page 13)

Diagnostic Points Table

Summarises running and standby electrical values 

for all components. 

(page 18) 

Wiring Diagram

(page 17)

Maintenance

Monitor / Error 

History

Provides accumulated 

number of startups, 

combustion time, history 

of operational faults and 

readout of electrical values 

whilst unit operational.

(page 25)

Component and 

Circuit Check 

Procedures

Detailed information on 

how to check all 

components.

(page 21)

Содержание REU-VR2426WS Solar 26






















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды