manualshive.com logo in svg

Rinnai REU-VR2426WS Solar 26, Руководство по обслуживанию

Поделиться
Скачать
Rinnai REU-VR2426WS Solar 26 Скачать руководство пользователя страница 33

REU-VR2626WB (B26) /REU-VR2426WS (S26) /REU-VRM2626WG (INF26)

- 29 -

Issue 3 - 13/11/14 ©Rinnai

IMPORTANT

For some areas of dismantling you may need to 
isolate any or all of the following:
* Isolate gas supply.
* Disconnect electrical supply from wall socket.
* Isolate water supply.
* Drain 

all

 water from appliance.

1)

Removal of the

 Front Panel

a. Remove four (4) screws.

2)

Removal of the 

PCB Unit

a. Remove the front panel. (Refer Item 1.)
b. Remove two (2) PCB unit fixing screws and pull 

out forward.

3)

Removal of the 

Water Flow Sensor, 

Servo and Bypass Servo

a. Remove the front panel. (Refer Item 1.)
b. Remove two (2) screws and locking plates 

located on the water supply pipe and bypass 
pipe. Pull bypass pipe and water supply pipe 
forward to clear servo valves. Ensure O-rings 
are not lost or damaged.

4) Removal of the Bypass Servo 

(2630 ONLY)

a. Remove two (2) screws from the water flow 

servo body, and pull the bypass servo out 
forwards. Ensure O-rings are not lost or 
damaged.

Содержание REU-VR2426WS Solar 26






















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды