Rinnai RCE-460PTR Скачать руководство пользователя страница 31

Страница: 31 / 71

Convector 460/560PTR

- 26 -

©Rinnai

Heater OFF

ON/OFF Switch OFF

Display

Room Temp.

Time

SV1 SV2 OFF

Mod. valve OFF

C.M. (med) ON

C.M. OFF

OFF TIMER

ON/OFF switch ON

Air volume indicator

illuminates (auto)

Dust indicator

illuminates (Green)

Air Purification

motor Hi ON

OFF timer switch ON

OFF Timer indicator

illuminates (1 hour)

Set up time
has passed

OFF timer sw. change

ON/OFF Switch OFF

Air Purifying ON

Dust indicator OFF

Air Purification motor

OFF

Air volume Ind. OFF

Yes

Air Purifying OFF

ON/OFF switch ON

Air volume indicator

illuminates (auto)

Dust indicator

illuminates (Green)

Air Purification

motor Hi ON

Automatic

operation

Operation ceases

TIMER

(150~255 sec)

ON/OFF switch ON

Combustion A -> B

Timer switch ON

Display

Room Temp.

Time

SV1 SV2 OFF

POV OFF

C.M. (med) OFF

Timer Ind. illuminates

Operation/comb. Ind.

illuminates (Green)

C.M. OFF

Pre-heat

time

Timer Indicator flashes

*When Timer 1 or Timer 2 is set up, the heater

will operate 1 cycle per day. (Within dotted line)

Then Timer 1 and Timer 2 are set up, the heater
will operate 2 cycles per day. (Within dotted line)

Dust Ind.

lluminates (Orange)

All Indicators OFF

Combustion A -> B

Yes

Timer off

set up time

Air Purificaiton

motor med ON

Dust Ind.

illuminates (Green)

Air Purificaiton

motor Lo ON

Dust Ind.

illuminates (Red)

Air Purificaiton

motor Hi ON

Safety device

activated

Yes

Air volume ind

Lo-Med-Hi-Boost

Air purification motor

Lo-Med-Hi-Boost

Dust indicator

Green-orange-Red

Cause elimated

All indicators OFF

ON/OFF switch OFF

Air purification motor OFF

Dust indicator OFF

Air volume indicator OFF

Operation/combustion

indicator flashes (Red)

Pre-filter comes off

detection

Yes

Содержание RCE-460PTR








































































Результаты поиска

Содержание RCE-460PTR

Отзывы:

Бренды по названию

Популярные бренды

Rinnai RCE-460PTR, Руководство по обслуживанию

Результаты поиска

Содержание RCE-460PTR

Отзывы:

Бренды по названию

Популярные бренды