background image

 

Rinnai Corporation ES08 Manual 

                                                       3 

     

WARNING

 

     

CAUTION

 

  Safety Behavior and Practices

 

 

 

 

 

 

 

 

 

 

 

 

 

 

    

• 

Do not block the warm air discharge.  Do not allow 
anyone to sleep directly in front of the appliance. 

• 

Due to high temperatures, the appliance should be 
located out of traffic and away from furniture and 
draperies. 

• 

Children and adults should be alerted to the 
hazards of high surface temperature and should 
stay away to avoid burns or clothing ignition.   

• 

Young children should be carefully supervised 
when they are in the same room as the appliance. 

• 

Clothing or other flammable material should not be 
placed on or near the appliance. 

• 

Any safety screen or guard removed for servicing 
must be replaced prior to operating the appliance. 

• 

Do not insert items into the louvers. 

• 

Do not spray aerosols near the appliance while it is 
operating.  Most aerosols contain butane gas which 
is flammable. 

• 

Do not unplug the appliance while it is operating or 
while the fans are on. 

 

• 

Keep the area around the appliance clear and free 
from combustible materials, gasoline, and other 
flammable vapors and liquids. 

• 

Never store liquid propane containers indoors. 

• 

Do not use this appliance if any part has been 
under water.  Immediately call a qualified service 
technician to inspect the appliance and to replace 
any part of the control system and any gas control 
which has been under water. 

• 

This appliance is equipped with a three-prong plug 
for your protection against shock hazard and 
should be plugged directly into a properly grounded 
three-prong receptacle.  Do not cut or remove the 
ground prong from this plug. 

• 

Any alteration to the appliance or its controls can 
be dangerous. 

• 

Do not operate appliance with the panels removed, 
cracked or broken.  Replacement of the panels 
should be done by a licensed or qualified service 
person. 

Consumer Safety Information 

  Safety Definitions

   

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 
 

This is the safety alert symbol.  This symbol alerts you to potential hazards that can kill or hurt you and 

others.

 

Indicates an imminently hazardous situation which, if not avoided, will result in death or 
serious injury. 

Indicates a potentially hazardous situation which, if not avoided, could result in death or 
serious injury. 

Indicates a potentially hazardous situation which, if not avoided, could result in  minor or 
moderate injury.  It may also be used to alert against unsafe practices. 

     

DANGER

 

     

CAUTION

 

     

WARNING

 

Содержание ES08









































Отзывы: