manualshive.com logo in svg

Bryant CONDENSING GAS FURNACE 355MAV, Инструкция по установке, запуску и эксплуатации

Газовая печь Bryant CONDENSING GAS FURNACE 355MAV идет с руководством по установке, запуску и эксплуатации. Бесплатно загрузите руководство в формате PDF с нашего веб-сайта. Это незаменимый инструмент для правильной установки и использования этого отличного продукта. Скачать на {веб-сайте}.

Поделиться
Скачать
background image

NOTE:

Read the entire instruction manual before starting the

installation.

This symbol

→

indicates a change since the last issue.

Index

Page

SAFETY CONSIDERATIONS .....................................................2
DIMENSIONAL DRAWING........................................................3

Clearances to Combustibles......................................................4

CODES AND STANDARDS........................................................5
ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS........5
INTRODUCTION ..........................................................................6
APPLICATIONS............................................................................6

General ......................................................................................6
Upflow Applications.................................................................6
Downflow Applications ............................................................8
Horizontal Left (Supply-Air Discharge) Applications ..........10
Horizontal Right (Supply-Air Discharge) Applications ........12

LOCATION..................................................................................13

General ....................................................................................13
Low-Heat Only Installation ....................................................14
Furnace Location Relative to Cooling Equipment ................15
Hazardous Locations...............................................................15

INSTALLATION .........................................................................15

Leveling Legs (If Desired) .....................................................15
Installation In Upflow or Downflow Applications................15
Installation In Horizontal Applications ..................................17
Air Ducts.................................................................................18

General Requirements .......................................................18
Ductwork Acoustical Treatment .......................................18
Supply Air Connections ....................................................18
Return Air Connections.....................................................18

Filter Arrangement..................................................................18
Bottom Closure Panel.............................................................19
Gas Piping...............................................................................19
Electrical Connections ............................................................20

115-v Wiring......................................................................20
24-v Wiring........................................................................22
Accessories ........................................................................22

Direct Venting.........................................................................22

Removal of Existing Furnaces from

Common Vent Systems................................................22

Combustion-Air and Vent Piping .....................................25
Concentric Vent and Combustion-Air Termination

Kit Installation..............................................................31

Multiventing and Vent Terminations................................34

Condensate Drain....................................................................34

General...............................................................................34
Application.........................................................................34
Condensate Drain Protection.............................................35

START-UP, ADJUSTMENTS AND SAFETY CHECK......35

General...............................................................................35
Select Setup Switch Positions...........................................36
Prime Condensate Trap With Water.................................37
Purge Gas Lines ................................................................37
Sequence of Operation ......................................................37

Single-Stage Thermostat and Two-Stage Heating
(Adaptive Mode) ..........................................................37
Two-Stage Thermostat and Two-Stage Heating .........39
Cooling Mode...............................................................39
Thermidistat Mode .......................................................40
Super-Dehumidify Mode..............................................40
Continuous Blower Mode ............................................40
Heat Pump ....................................................................41
Component Test ...........................................................41

Adjustments .......................................................................41

Set Gas Input Rate .......................................................41
Set Temperature Rise...................................................48
Set Thermostat Heat Anticipator .................................49

A93040

ama

CERTIFIED

®

REGISTERED

ISO 9001:2000

As an ENERGY STAR®
Partner, Bryant Heating &
Cooling Systems has de-
termined that this product
meets

the

ENERGY

STAR® guidelines for en-
ergy efficiency.

Fig. 1—Multipoise Orientations

A93041

UPFLOW

DOWNFLOW

HORIZONTAL

LEFT

AIRFLOW

AIRFLOW

AIRFLOW

AIRFLOW

HORIZONTAL

RIGHT

installation, start-up,
and operating instructions

DELUXE 4-WAY MULTIPOISE
VARIABLE-CAPACITY DIRECT-VENT
CONDENSING GAS FURNACE

Cancels:

II 355M-40-13

II 355M-40-14

3-05

355MAV

Series I

—1—

Содержание CONDENSING GAS FURNACE 355MAV





















































Отзывы:

Нет отзывов

Похожие инструкции для CONDENSING GAS FURNACE 355MAV

Aire-Flo 95AF2DF045V12B Installation Instructions Manual preview
95AF2DF045V12B
Бренд: Aire-Flo Страницы: 52
Lennox G23 Series Installation Instructions Manual preview
G23 Series
Бренд: Lennox Страницы: 31
Coleman 035-16329-002 Owner'S Manual preview
035-16329-002
Бренд: Coleman Страницы: 8
Lenoxx G1D91BT Installation Instructions Manual preview
G1D91BT
Бренд: Lenoxx Страницы: 36
VERDER Carbolite HZS Series Installation, Operation & Maintenance Instructions Manual preview
Carbolite HZS Series
Бренд: VERDER Страницы: 16
Rinnai Energysaver RHFE-1004FTA Service Manual preview
Energysaver RHFE-1004FTA
Бренд: Rinnai Страницы: 112
Atwood HYDRO FLAME 2540 User Manual preview
HYDRO FLAME 2540
Бренд: Atwood Страницы: 6
Bard WG241D Installation Instructions Manual preview
WG241D
Бренд: Bard Страницы: 79
KERR COMPACT-multi Installation, Operation And Maintenance Manual preview
COMPACT-multi
Бренд: KERR Страницы: 25
KERR ECLIPSE 3T Installation, Operation And Service Manual preview
ECLIPSE 3T
Бренд: KERR Страницы: 35
Granby KLC-100 Installation, Operation And Service Manual preview
KLC-100
Бренд: Granby Страницы: 33
Granby KHM-1/090 Installation, Operation And Service Manual preview
KHM-1/090
Бренд: Granby Страницы: 35
Granby KLF-200 Installation, Operation And Service Manual preview
KLF-200
Бренд: Granby Страницы: 36
Granby KLF-100 Installation, Operation And Service Manual preview
KLF-100
Бренд: Granby Страницы: 40
Granby KHM SERIES Installation, Operation And Service Manual preview
KHM SERIES
Бренд: Granby Страницы: 39

Бренды по названию

Популярные бренды

Загрузить еще бренды