background image

Rinnai 

Ducted Gas Heater IM

NOTE

The manufacturer cannot guarantee compatibility and support for anyone using 3rd party 

accessory/devices (device) on any of their appliances.  
The suitability, compatibility or functional performance of any 3rd party device is entirely the 

responsibility of the device’s supplier or installer. 
Any 3rd party device, technical, installation, operation, performance or other enquiries need to be 

referred to the device’s supplier or installer. 

Any  adverse  effects  of  3rd  party  devices  on  the  operation,  performance  or  reliability  of  this 

appliance is not covered by the manufacturer’s product warranty. 

WARNING

MANDATORY INSPECTION PRIOR TO INSTALLATION

Immediately report any damage or discrepancies to the Supplier of the appliance. This 

appliance was inspected and tested at the time of manufacture and packaging, and released for 

transportation without known damage. Upon receipt, inspect the exterior for evidence of rough 

handling in shipment. Ensure that the appliance is labelled correctly for the gas and electrical 

supply, and/or other services it is intended to be connected to.   

For safety and warranty purposes, appliances that may be damaged or incorrect must not be 

installed or operated under any circumstances.  Installation of damaged or incorrect appliances 

may contravene local government regulations.  Rinnai disclaims any liability or responsibility 

whatsoever in relation to the installation or operation of damaged or incorrect appliances.

Содержание brivis StarPro BX5













































Отзывы: