background image

 

 

17

 

7.MEASURES AT ABNORMAL CASE 

 
 
7−1.Responding to trouble alarm 

If this detector founds defective, contact RIKEN KEIKI. 

 
 
7−2.Before it is thought to be a trouble 

 
 

  ・Check the wirings around the related instruments as well as this detector head. 

 

It may be caused by improper operation. 

  ・Re-check the detection system and contact RIKEN KEIKI. 

 
 
 
 

8.DEFINITION OF TERMS 

 
 
  Galvanic cell 

Galvanic cell type oxygen sensor that produces a current proportional to the oxygen content 
permeated through the membrane.    Refer to  「10. DETECTION PRINCIPLE」  for details. 

 
  Zener barrier 

Safety  retainer  for  explosion  protection  by  limiting  the  energy  of  electric  current  within  a 
non-ignition level. 

 
  CVVS 

This is a kind of connecting cable between indicator/alarm unit and oxygen detector head. 
CVVS means a “Polyethylene insulated and vinyl sheathed control cable with shield”. 

 
  Calibration 

By  using  standard  (calibration)  gas,  adjust  gas  reading  in  indicator/alarm  unit  to  match  the 
calibration gas concentration.   

 

It may be caused by cable disconnection, short circuit, etc. 

Содержание GD-F4A-1























Отзывы: