Rigol DS6000 Series Скачать руководство пользователя страница 10

Страница: 10 / 54

Chapter 2 Quick Start

RIGOL

User’s Guide for DS6000 Demo Board 2-7

2.2 Measurement Connection

Connect the signal output terminals of the Demo board to the corresponding input terminals of the
oscilloscope before using the Demo board.

Connection Method:

Connect the BNC terminal of the probe to one of the BNC connectors of input channels (CH1-CH4) at
the front panel of the oscilloscope.

Connect the probe tip to the corresponding signal output pin on the Demo board and connect the
ground alligator clip of the probe to the ground terminal (GND) of the Demo board.

2.3 Demo Board Power-on

The Demo board can be powered through the USB port. Connect the

USB DEVICE

interface of the Demo

board with the

USB HOST

interface of the oscilloscope or PC using USB data cable.

Note:

The

icon at the upper-right corner of the board indicates that static electricity would cause

Demo board damage and the board should be used in anti-static environment as far as possible.

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Содержание DS6000 Series























































Результаты поиска

Содержание DS6000 Series

Отзывы:

Похожие инструкции для DS6000 Series

Бренды по названию

Популярные бренды

Rigol DS6000 Series, Руководство пользователя

Результаты поиска

Содержание DS6000 Series

Отзывы:

Похожие инструкции для DS6000 Series

Бренды по названию

Популярные бренды