Riello SC SUN 300 Скачать руководство пользователя страница 29

Страница: 29 / 36

ENGLISH

MALFUNCTIONS

MALFUNCTIONS WITH ERROR MESSAGES

The controller indicates a problem by causing the LED

to blink red and generating a relative error symbol in the

display. If the error is only transient, the error symbol will

be replaced by an information symbol and the blinking

red light disappears.

To find out more about an error, press the key located be-

low the error or information symbol.

Do not attempt to solve the problem without assis-

tance. Always call an expert service technician.

esc

Flashing LED +

warning symbol

Possible error messages

Notes for service technicians

Sensor x defective

Fault affecting the sensor, the sensor input at the controller, or the cable connecting

the sensor.

Collector alarm

This alarm will trip when the collector temperature limit set by way of the menu "5.6.

Collector alarm" is exceeded.

Restart

This indicates that the controller has rebooted, e.g. following an electrical power

failure. Check the date and time

Time & date

This screen appears automatically following an electrical power failure, since the

time and date must be verified, and if necessary reset.

Night-time circulation

Check clock

This indicates that the pump is or was in operation between 23:00 and 04:00.

System protection

The collector temperature setting was exceeded at some point, triggering deactiva-

tion of the solar pump to prevent damage to the system through overheating.

Collector protection

The collector temperature setting was exceeded at some point, triggering activation

of the solar pump to cool the collector circuit with the aid of the heat exchanger.

Recooling

Excess heat was or is being radiated from the collector to protect the system.

Frost protection

The solar pump was switched on to prevent frost damage to the collector

Frequent On / Off

When the solar pump is switched on and off more than 5 times in 5 minutes (i.e. 11

contact changes), this message is displayed.

No flow

Message displayed when the solar pump is running with ΔT >= 50 °C for at least 5

minutes.

Pressure: failure

Displayed when pressure monitoring is activated and the Pmin or Pmax limit is

exceeded.

SD-card error

This message is displayed when an SD card has been detected, but the controller

is unable to read from or write to the card.

Содержание SC SUN 300





































Результаты поиска

Содержание SC SUN 300

Отзывы:

Бренды по названию

Популярные бренды

Riello SC SUN 300, Руководство пользователя

Результаты поиска

Содержание SC SUN 300

Отзывы:

Бренды по названию

Популярные бренды