Riello NexPro Plus Скачать руководство пользователя страница 5

5

GENERAL CHARACTERISTICS

 

1 .4 

General description

The heat pump heaters 

R

 NexPro Plus use the thermal energy 

of the air to produce domestic hot water.

Ease of installation, noiseless and reliable operation and min-

imum maintenance requirements complete the advantages of 

this highly ecological and economical system.

The unit is suitable for indoor installation and uses as standard 

alternative energy source a 1.5 kW single-phase electric heating 

element. The accumulation tank is made of carbon steel, with 

internal 2-layer glazing, magnesium anode, internal coating in 

rigid plastic material (ABS).

1 .5 

Operating principle of the heat pump

The operating principle of the heat pump is the following:

 

− The refrigerating fluid changes its state in the evaporator 

(1)  taking  heat  from  the  low  temperature  source  (the 

external air).

 

− The compressor (2), that is the heart of the system, makes 

the energy level of the taken heat higher: in fact, the 

refrigerating  fluid,  by  increasing  its  pressure,  reaches 

temperatures near to 90°C.

 

− In the condenser (3)  it is possible to give thermal energy 

to the domestic hot water, warming it until 60°C.

 

− The  storage  tank  (4)  (300  litres)  allows  storing  up  and 

keeping for a long time the heat, thanks to insulating 

shell in polyurethane 50mm thick.

 

− Crossing in the end the expansion element (5), the fluid 

returns to low pressure, cools down and it is available 

to “load” other “ecological” heat again from external air.

 

− the  solenoid  valve  (6)  allows  to  equalize  pressures 

during the starting phase and, if necessary, allows the 

evaporator defrost.

1

2

3

4

5

6

Evaporator

2  Compressor

3  Condenser

4  Storage tank

5  Electronic expansion valve

6  Solenoid valve

1 .6 

Constructive characteristics

The main constructive features of the heat pump heaters 

R

 

NexPro Plus are:

 

− carbon steel tank with double-layer glazing

 

− capacitor externally wrapped to the accumulation 

tank free from limescale deposits and gas-water 

contamination

 

− auxiliary coil for the use in combination with boilers 

(

NexPro 300 CS Plus

) or solar panels (

NexPro 300 S Plus, 

NexPro 300 CS Plus

)

 

− NTC integrated probe for the control of water temperature.

 

− NTC outdoor temperature sensor for automatic insertion 

of the electrical heater with temperature not favourable 

to the heat pump.

 

− evaporating coil input/output NTC probes

 

− electronic thermostatic valve

 

− solenoid  valve  for  hot  gas  injection  and  pressure 

equalisation

 

− anti-corrosion magnesium anode

 

− hydraulic connections on the back side

 

− condensate drain integrated in the isolation

 

− hermal insulation with injected polyurethane with high 

thickness

 

− external coating in RAL 7001 grey plastic

 

− use of refrigerant gas R134A

 

− single phase 1.5 kW electrical heater

 

− safety devices for high pressure

 

− high efficiency rotary compressor

 

− variable speed radial fan

 

− support handles for easy and safe transport.

The management, fully electronic, is provided with:

 

− User interface for setting the operative mode and set the 

parameters with different levels of accessibility protected 

by password

 

− self-diagnosis and display of alarms (high pressure, high 

temperature of water, probes disconnected)

 

− storage of runtime and clock function

 

− water set-point adjustment for automatic and/or manual 

operation

 

− outdoor air temperature display

 

− modulating fan speed control

 

− dynamic set point function

 

− management of minimum time intervals between 

successive starts of the compressor

 

− remote ON/OFF for complete unit (timer)

 

− remote ON/OFF for electrical heater (energy twin rate)

 

− electrical heater management in manual or automatic 

integration mode with low outdoor temperature

 

− command to an external boiler as an alternative to the 

electric heating element

 

− insertion of the cyclic antibacterial treatment to eliminate 

and prevent the formation of legionella

 

− defrost management through hot gas by-pass.

Содержание NexPro Plus





























Отзывы: