Riello Family IS, Инструкция по установке и эксплуатации

Страница: 24 / 196

FAMILY
24
Boiler faults list
ERROR
CODE
COLOUR
DISPLAYED
ERROR MESSAGE
DESCRIPTION OF TYPE OF
ALARM
E010 Yellow flame lockout/ACF electronic fault definitive
E011 Yellow extraneous flame transitional
E020 Red limit thermostat definitive
E030 Red fan fault definitive
E040 Yellow water transducer – load system definitive
E041 Yellow water transducer – load system transitional
E042 Yellow water pressure transducer fault definitive
E060 Yellow storage cylinder faulty transitional
E070 red
flow sensor faulty
flow sensor overtemperature
flow/return sensor differential alarm
transitional
definitive
definitive
E077 Red main zone water thermostat transitional
E080 Yellow
return line probe fault
return line probe overtemperature
outlet/return line probe differential alarm
transitional
definitive
definitive
E090 Red
flue gas probe faulty/
flue gas probe overtemperature
transitional
definitive
E091 Yellow clean primary heat exchanger transitional
E099
It is referred to the
last fault occurred
reset attempts exhausted, boiler blocked
definitive,
not resettable
-- Yellow water pressure low check system transitional
-- Red water pressure high check system transitional
-- Red boiler board communication lost transitional
-- Red BUS 485 communication lost transitional
List of combustion faults
ERROR
CODE
COLOUR
DISPLAYED
ERROR MESSAGE DESCRIPTION OF TYPE OF ALARM
E021 Red ACC monitor error
These are temporary alarms that if they occur 6 times in an hour they become definitive; the alarm E097 is displayed
and is followed by post-purging for 45 seconds at the fan's maximum speed.
It is not possible to release the alarm before the end of the post-purging unless the boiler's power supply is switched
off.
E022 Red ACC monitor error
E023 Red ACC monitor error
E024 Red ACC monitor error
E067 Red ACC monitor error
E088 Red ACC monitor error
E097 Red ACC monitor error
E085 Red incomplete combustion
These are temporary alarms that if they occur several times in an hour they become definitive; the last error to occur
is displayed and is followed by a post-purging of 5 minutes at the fan's maximum speed.
It is not possible to release the alarm before the end of the post-purging unless the boiler's power supply is switched
off.
E094 Red incomplete combustion
E095 Red incomplete combustion
E058 Red mains voltage fault
Si These are temporary faults that restrict the ignition cycle.
E065 Red current modulation alarm
E086 Red flue gases obstruction alarm Temporary fault signalled during Pre-Purging. Post-Purging is maintained for 5 min at maximum fan speed.
5.16 Error history
The ERROR HISTORY function is automatically enabled only after the machine has been
powered up for at least 2 consecutive hours, during this period of time any alarms that arise
would not be saved in the “error history ”. The alarms can be displayed in chronological order,
from the most recent to the oldest, up to a maximum of 50 alarms; to display the error history:
- access the technical parameters as explained in the section“ Accessing the technical
parameters”
- select ERROR HISTORY with the "UP" and "DOWN " keys, confirming the selection
EXHAUST PROBE RESET
COMBUSTION ANALYSIS
CALIBRATION
RANGE RATED
ERROR HISTORY
TECHNICAL
INSTALLER

- scroll through the alarms log with the “UP” and “DOWN ” keys; for each alarms a
sequential number is displayed, an error code and the date and time the alarm occurred.
FAN ERROR
1 - 10:30 18/11/2013
E030
USE ARROW KEYS TO SEE OTHER ANOMALIES
It is possible to return to the start page at any time by keeping the “BACK” key pressed
for at least 2 seconds.
Note: Once enabled, the ERROR HISTORY function can no longer be disabled; there is no
procedure for resetting the error history.
If an alarm repeats consecutively, it is saved only once.
The alarms log contains both boiler alarms as well as alarms regarding the heat pump.
5.17 Temporary switch-off
In the event of temporary absences (weekends, short breaks, etc.) set the status of the
boiler to OFF .
OFF
HOT WATER ONLY
HEATING AND HOT WATER
BOILER
While the electrical supply and the fuel supply remain active, the boiler is protected by the
systems:
-
heating anti-freeze: this function is activated if the temperature measured by the flow
sensor drops below 5°C. A heat request is generated in this phase with the ignition of the
burner at minimum output, which is maintained until the outlet water temperature reaches
35° C;