11 — English
ASSEMBLY
UNPACKING
This product requires assembly.
Carefully cut the box down the sides then remove the
machine and any accessories from the box. Make sure that
all items listed in the loose parts list are included.
NOTE:
This machine is heavy and requires a minimum of
two people to lift. To avoid back injury, lift with your legs and
not your back.
WARNING:
Do not use this product if any parts on the Loose
Parts List are already assembled to your product
when you unpack it. Parts on this list are not
assembled to the product by the manufacturer and
require customer installation. Use of a product that
may have been improperly assembled could result in
serious personal injury.
Inspect the product carefully to make sure no damage
occurred during shipping.
Do not discard the packing material until you have carefully
inspected and satisfactorily operated the product.
If any parts are damaged or missing, please call
1-866-539-1710, for assistance.
WARNING:
If any parts are damaged or missing do not operate
this product until the parts are replaced. Use of this
product with damaged or missing parts could result
in serious personal injury.
WARNING:
Do not attempt to modify this product or create
accessories not recommended for use with this
product. Any such alteration or modification is misuse
and could result in a hazardous condition leading to
possible serious personal injury.
WARNING:
Do not attempt to operate the generator until
assembly is complete. Failure to comply could result
in possible serious personal injury.
LOOSE PARTS LIST
See Figure 3.
The following items are included with the generator:
Key
No. Description
Qty.
1 Axle ......................................................................... 2
2 Spacer ..................................................................... 2
3 Wheel ...................................................................... 2
4
Washer (5/8 in.) ....................................................... 4
5
Hitch Pin ................................................................. 2
LOOSE PARTS LIST
(continued)
Key
No. Description
Qty.
6
Lock Nut (M6) ......................................................... 2
7
Legs with Rubber Feet (Left and Right) .................. 2
8
Bolt (M6 x 50) .......................................................... 2
9 Bolt (M5 x12) ........................................................... 2
10
Flat Washer (M5) ..................................................... 2
11
Lock Washer (M5) ................................................... 2
12
Lock Nut (M5) ......................................................... 2
13
Engine Lubricant ..................................................... 1
Operator’s Manual (not shown) ............................... 1
TOOLS NEEDED
See Figure 4.
The following tools (not included or drawn to scale) are needed
for assembly:
8 mm and 10 mm Socket Wrench
8 mm and 10 mm Combination Wrench
Phillips Screwdriver
NOTE:
Do not put fuel or lubricant in the generator before
installing the legs and wheels.
INSTALLING LEGS
See Figure 5.
Locate the following items:
Legs with rubber feet (left and right)
2 lock nuts (M6)
2 bolts (M6 x 50)
Raise the front end of the generator, where the engine is
located, high enough to gain access to the frame bottom;
securely position props underneath to support.
Slide a leg onto the stud on one side of the frame support.
Position the leg so that the holes in the leg align with the
holes in the frame.
Insert bolt through hole in the frame and the leg.
Fasten the bolt by installing a lock nut over bolt on the inside
of the frame. Tighten the nut securely.
Repeat with remaining leg.
INSTALLING THE WHEELS
See Figure 6.
Wheels are provided to assist in moving the generator to the
desired location and should be installed on the side opposite
the recoil starter.
Locate the following items:
2 axles
2 spacers
4 washers (5/8 in.)
2 hitch pins
2 wheels
Raise the handle end of the generator high enough to gain
access to the frame bottom; securely position props under-
neath to support.
Insert the axle bolt through the spacer, then into the center
of the wheel.