Ricoh fax5600 Скачать руководство пользователя страница 235 | Manualshive

Страница: 235 / 269

background image

Problem

Required Action

Transmission cannot take
place; the Clear
Original indicator blinks.

The document is jammed in the feeder.

➣

Remove the jammed document (see page 213)
and repeat the transmission procedure.

The document may be longer than the maximum limit (see
page 45).

➣

Make sure that none of your originals exceed
this limit.

Do user maintenance, especially rollers [J] and [H] (see page
203).

➣

If the same problem still exists after user
maintenance, adjust the auto document
feeder mechanism (see page 214).

Transmission cannot take
place; the Line Fail indicator
blinks.

Note: Before taking action,
wait until the Communicating
indicator goes out, then press
the Stop key.

The other machine is out of order.

➣

Check the error report.

➣

Ask the other party to check their machine
and correct the fault.

The line is busy or noisy.

➣

Check that the dial tone is sent out.
Try to retransmit.

Consistent difficulty in
communicating with a
particular terminal

There are some bad lines between you and that other
terminal.

➣

Store that terminal’s number as a Quick Dial
Key or Speed Dial Code.
Then call a service technician. Inform the
nature of the problem and give the Quick Dial
Key or Speed Dial Code that you stored the
number in.

Consistent poor image quality
when communicating with a
particular terminal

RECEPTION

The telephone keeps ringing
and no fax is printed.

You are in Manual Receive mode.

➣

Change to Auto Receive mode (see page 74).

Power is switched off.

➣

Switch the power on.

RECEPTION/COPYING

No printout; the Add Paper
indicator is lit.

The cassettes are empty.

➣

Add paper (see page 194).

No printout; the Clear
Copy indicator blinks.

The printer has jammed.

➣

Clear the jam (see page 215).

Do user maintenance, especially rollers [N], [L], and [U] (if the
lower cassette is installed). See page 203.

Copies appear dirty.

Does the original have a gray or colored background?

➣

Select the Lighten contrast setting.

Copies are too light.

Does the original have a low contrast image?

➣

Select the Darken contrast setting.

Copies are blank.

The original must be placed face down in the document feeder

➣

Position the original correctly. See page 49.

SO

LV

IN

G

P

R

O

B

L

E

M

S

SOLVING PROBLEMS

OPERATING DIFFICULTIES

221

«
...
233
234
235
236
237
...
»

Содержание fax5600














































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для fax5600

DocuPrint 4850 NPS

Бренд: Xerox Страницы: 276

Pro-LX Pro-LX Laminating Card...

Бренд: FARGO electronics Страницы: 228

Бренд: Konica Minolta Страницы: 404

WorkCentre 6400XF

Бренд: Xerox Страницы: 24

Бренд: B-G Instruments Страницы: 2

5550N - Phaser B/W Laser Printer

Бренд: Xerox Страницы: 16

Бренд: Tektronix Страницы: 178

Бренд: OKIDATA Страницы: 158

Бренд: Xerox Страницы: 16

Бренд: WOOSIM Страницы: 25

DIDSON ARIS EXPLORER 3000

Бренд: Sound Metrics Страницы: 22

Бренд: HPRT Страницы: 7

Бренд: HPRT Страницы: 28

Бренд: HPRT Страницы: 35

Бренд: HPRT Страницы: 46

Бренд: HPRT Страницы: 101

Бренд: Ricoh Страницы: 90

Бренд: Ricoh Страницы: 141

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды