Rice Lake ELS Series Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 30

background image

Introduction

©

Rice Lake Weighing Systems

●

All Rights Reserved

5

1.5 Grounding Straps

The grounding straps connected to the ELS weigh stands are used to ground the conveyor to the floor. If the system is not

properly grounded, static can build up and cause damage to the load cells once the static discharges. The grounding straps

protect the load cells by providing an alternate path for the static discharge to travel.
The grounding straps are located on each load cell assembly and connect the load cell top plate to the mounting plate.

Figure 1-2. Grounding Straps

The grounding straps must be connected to the weigh stands at all times.

Grounding Strap

IMPORTANT

«
...
7
8
9
10
11
...
»

Содержание ELS Series































Отзывы:

Нет отзывов

Похожие инструкции для ELS Series

Бренд: GALTRONICS Страницы: 3

Бренд: peerless-AV Страницы: 58

Ergo D-ProNotebook Stand

Бренд: Targus Страницы: 14

Бренд: HoverCam Страницы: 7

Бренд: OEM Tools Страницы: 4

Mailbox Protector

Бренд: CDP Страницы: 2

Бренд: ASTRALVISION Страницы: 3

Бренд: B-Tech Страницы: 16

Бренд: Eagle Group Страницы: 2

Бренд: Black Box Страницы: 2

Бренд: CIM med Страницы: 12

Бренд: NCR Страницы: 14

RACK2100 Series

Бренд: 3onedata Страницы: 5

Бренд: BalanceBox Страницы: 2

Бренд: Crestron Страницы: 2

Бренд: AEG Страницы: 16

Бренд: AEG Страницы: 62

Бренд: AEG Страницы: 128

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды