RHINO MNVR Series Скачать руководство пользователя страница 23

Страница: 23 / 206

Step 2 Push the SIM card slot to the back and open the SIM card slot.
Step 3 Insert the SIM card and then close the cover.

Figure 2-11

Note

After install the SIM card, make sure you have properly secure the card slot in case it
becomes damaged when remove the HDD box.

Step 4 Insert HDD box.

2.5 HDD Installation

2.5.1

HDD Installation

HDD is not standard accessories. Please purchase separately and follow the contents listed
below to install.

Note



Shut down the device and unplug the power cable before install/remove the HDD.



The e-lock on the right side of the front panel shall be unlocked when you install/remove the

HDD. Please lock the button before you boot up the device.

System does not have the HDD or SD card by default. Please follow the steps listed below to
install.

Important



Shut down the device and unplug the power cable before install/remove the HDD.

Step 1 Remove the HDD box cover.
Step 2 Loosen the screws of the bottom board of the HDD box and then remove the bottom

board. Now you can see an interface shown as in Figure 2-12.

Содержание MNVR Series















































































































































































































Результаты поиска

Содержание MNVR Series

Отзывы:

Бренды по названию

Популярные бренды

RHINO MNVR Series, Руководство пользователя

Результаты поиска

Содержание MNVR Series

Отзывы:

Бренды по названию

Популярные бренды