Rheem PVCG Скачать руководство пользователя страница 6

6

 

 

LOCATION REQUIREMENTS AND CONSIDERATIONS

WARNING

 

IT IS NOT DESIRABLE TO INSTALL A GAS FIRED WATER HEATER IN A 
RESIDENTIAL GARAGE. IF INSTALLATION IN A RESIDENTIAL GARAGE IS 
YOUR ONLY OPTION, THIS WATER HEATER MUST BE INSTALLED SUCH 
THAT THE PILOT FLAME AND MAIN BURNER FLAME ARE NO LESS THAN

 

18 INCHES ABOVE THE FLOOR (SEE FIGURE 2 BELOW).

 THIS IS TO 

REDUCE

 BUT NOT ELIMINATE 

THE RISK OF IGNITING FLAMMABLE 

VAPORS WHICH MAY BE PRESENT IN A GARAGE.

 THE WATER HEATER 

MUST BE LOCATED OR PROTECTED TO AVOID PHYSICAL DAMAGE 
BY VEHICLES OR FLOODING. FAILURE TO FOLLOW THESE 
WARNINGS CAN CAUSE A FIRE OR EXPLOSION, RESULTING IN 
PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. 

SITE LOCATION 

1. 

Select a location near the center of the water piping system.  It must 

be installed indoors and in a vertical position on a level surface. 

DO 

NOT

 install in bathrooms, bedrooms or any occupied room normally 

kept closed.

 

2. 

Locate the water heater as close to the chimney or gas vent as is 

practical. Consider the vent system piping  and combustion air supply 

requirements when selecting the water heater location. The venting 

system must be able to run from the water heater to the termination 

with a minimal length and elbows.  

THE VENT PIPE CANNOT 

EXCEED THE MAXIMUM ALLOWABLE LENGTH OF 40 FEET WITH 

3 LONG RADIUS ELLS. 

3. 

Locate the water heater near the existing gas piping. If installing a new 

gas line, locate the water heater to minimize the pipe length and 

elbows.

 

 

IMPORTANT

 

 

4. 

The water heater should be located in an area where leakage of the 

tank or connections will not result in damage to the area adjacent to 

the water heater or to lower floors of the structure. It is recommended 

that a suitable drain pan be installed under the water heater as shown 

above. This pan is to protect the property from damage which may 

occur from normal condensate formation on the tank jacket or leaks in 

the tank and pipe connections. The pan must limit the water level to a 

maximum depth of 1 3/4 inches and be two inches wider than the 

heater and piped to an adequate drain. Locate the water heater near a 

suitable inside drain. Outside drains are subject to freezing 

temperatures. The piping should be at least 3/4” ID and pitched for 

proper drainage. This pan must not restrict combustion air flow. 

UNDER NO CIRCUMSTANCES IS THE MANUFACTURER TO BE 

HELD LIABLE FOR ANY WATER DAMAGE IN CONNECTION WITH 

THIS WATER HEATER. 

 

 

5. 

The water heater should be located in an area not subject to freezing 

temperatures. Water heaters located in unconditioned areas (i.e. attics, 

basements, etc.) may require the insulation of the water piping and drain 

piping to protect against freezing. The drain and controls must be easily 

accessible for operation and service. 

Maintain proper clearances as specified.

  

6. 

Do not locate the water heater near an air-

moving device. The operation of air-moving 

devices such as exhaust fans, ventilation 

systems, clothes dryers, fireplaces, etc., 

can affect the proper operation of the 

water heater. Special attention must be 

given to conditions these devices may 

create to avoid unsatisfactory operation 

of the equipment.

 

CLEARANCE/ACCESSIBILITY

 

Minimum clearances from combustible materials are stated on the data plate 

adjacent to the thermostat of the water heater. 

REFER TO THE DATA 

PLATE OF THE WATER HEATER FOR THE CORRECT CLEARANCES 

FROM COMBUSTIBLE CONSTRUCTION MATERIALS.

 Figure 3 may be 

used as a reference guide to locate the specific clearance locations. A 

minimum of 24 inches of front clearance should be provided for inspection and 

service.

 

WARNING 

THE WATER HEATER IS CERTIFIED FOR INSTALLATION ON A 
COMBUSTIBLE FLOOR. HOWEVER, WHEN THIS WATER HEATER IS 
INSTALLED OVER CARPETING, THE CARPETING MUST BE PROTECTED 
BY A METAL OR WOOD PANEL BENEATH THE WATER HEATER AND 
EXTENDING BEYOND THE FULL WIDTH AND DEPTH OF THE WATER 
HEATER BY AT LEAST THREE INCHES IN ANY DIRECTION. IF THE 
WATER HEATER IS INSTALLED IN A CARPETED ALCOVE OR CLOSET, 
THE ENTIRE FLOOR MUST BE COVERED BY THE PANEL. FAILURE TO 
FOLLOW THESE INSTRUCTIONS MAY RESULT IN A FIRE HAZARD.

 

 

 

 

Содержание PVCG




























Отзывы: