background image

 

 

Page 21 of 22 

RHEEM UV DISINFECTION WARRANTY - AUSTRALIA ONLY 

UV DISINFECTION MODELS  940 001, 940 002  

1.

 

THE RHEEM WARRANTY – GENERAL 

1.1

 

This warranty is given by Rheem Australia Pty Limited ABN 21 098 823 511 of 1 Alan Street, Rydalmere New South Wales. 

1.2

 

Rheem offer a trained and qualified national service network who will repair or replace components at the address of the UV unit subject to 
the terms of the Rheem warranty. Rheem Service, in addition can provide preventative maintenance and advice on the operation of your 

UV unit. The Rheem Service contact number is available 7 days a week on 131031 with Service personnel available to take your call from 
8am to 8pm daily (hours subject to change). 

1.3

 

For details about this warranty, you can contact us on 131031 or by email at 

[email protected]

 (not for service bookings). 

1.4

 

The terms of this warranty are set out in section 2 and apply to UV units manufactured after 1

st

 January 2012. 

1.5

 

If a subsequent version of this warranty is published, the terms of that warranty will apply to UV units manufactured after the date specified 
in the subsequent version. 

2.

 

TERMS OF THE RHEEM WARRANTY AND EXCLUSIONS TO IT 

2.1

 

The decision of whether to repair or replace a faulty component is at Rheem’s sole discretion. 

2.2

 

If you require a call out and we find that the fault is not covered by  the Rheem warranty, you are responsible for our standard call out 
charge. If you wish to have the relevant component repaired or replaced by Rheem, that service will be at your cost. 

2.3

 

Where  a  failed  component  is  replaced  under  this  warranty,  the  balance  of  the  original  warranty  period  will  remain  effective.  The 

replacement does not carry a new Rheem warranty. 

2.4

 

Where the Rheem UV system is installed outside the boundaries of a metropolitan area as defined by Rheem or further than 25 km from 
either  a  regional  Rheem  branch  office  or  an  Accredited  Rheem  Service  Agent's  office,  the  cost  of  transport,  insurance  and  travelling 
between the nearest branch office or Rheem Accredited Service Agent’s office and the installed site shall be the owner’s responsibility. 

2.5

 

Where the Rheem UV system is installed in a position that does not allow safe or ready access, the cost of that access, including the cost 
of additional  materials handling and/or safety  equipment, shall be the owner’s responsibility. In other  words, the cost of  dismantling or 

removing cupboards, doors or walls and the cost of any special equipment to bring the UV unit to floor or ground level or to a serviceable 
position is not covered by this warranty. 

2.6

 

This warranty only applies to the original and genuine Rheem UV unit in its original installed location and any genuine Rheem replacement 
parts. 

2.7

 

The Rheem warranty does not cover faults that are a result of: 
a)

 

Accidental damage to the UV unit or any component (for example: (i) Acts of God such as floods, storms, fires, lightning strikes and the 

like; and (ii) third party acts or omissions). 

b)

 

Misuse or abnormal use of the UV units. 

c)

 

Installation not in accordance with the Owner’s Guide and Installation Instructions or with relevant statutory and local requirements in 

the State or Territory in which the UV unit is installed. 

d)

 

Connection at any time to a water supply that does not comply with the water supply guidelines as outlined in the Owner’s Guide and 

Installation Instructions. 

e)

 

Repairs, attempts to repair or modifications to the  UV unit by a person other than Rheem  Service or a Rheem  Accredited Service 

Agent. 

f)

 

Faulty plumbing or faulty power supply. 

g)

 

Failure to maintain the UV unit in accordance with the Owner's Guide and Installation Instructions. 

h)

 

Transport damage. 

i)

 

Fair wear and tear from adverse conditions (for example, corrosion). 

j)

 

Cosmetic defects. 

k)

 

For a UV lamp, more than (4) ON/OFF switches per 24 hour period, or where the time from delivery has exceeded 30 months, whether 

the UV lamps are installed and operating or not.(lamps have a 30 month shelf life.) 

2.8

 

Subject  to  any  statutory  provisions  to  the  contrary,  this  warranty  excludes  any  and  all  claims  for  damage  to  furniture,  carpet,  walls, 
foundations or any other consequential loss either directly or indirectly due to leakage from the UV unit, or due to leakage from fittings and/ 

or pipe work of metal, plastic or other materials caused by water temperature, workmanship or other modes of failure. 

2.9

 

If the UV unit is not sized to supply the UV demand in accordance with the guidelines in the Rheem UV unit literature, any resultant fault 
will not be covered by the Rheem warranty. 

Содержание 940001























Отзывы: