Rheavendors Group Horeca Large 380 Скачать руководство пользователя страница 32

Страница: 32 / 33

The display shows

"OFF 31C” the
machine is out of
order

Temperature probe cut off

Change the temperature probe

Il display shows
"

PLEASE LOAD

THE MASTER
PROGRAM

It has not been loaded any
master program in the CPU
board

Ask to Rhea technical service the correct
master file and load the file master with
flash card into the machine

17.2 Miscellaneous shortcomings

The shortcomings described in this section are not indicated by any message displayed on the machine.

SYMPTOM

PROBABLE CAUSE

SOLUTION

The machine does not switch
on (no component is
powered)

No mains voltage

Wait for the resetting of mains voltage

The boiler is overheated

Reset the safety thermal switch boiler.
Check the correct operation and cable of the
thermal probe or the resistance in the boiler
and replace them if necessary

One general fuse) is burnt
out

Replace it

The general safety switch
is faulty

Replace it

The machine does not switch
on (some components are
powered but the display is
off)

The fuse on the CPU
board (8.5 V) is burnt out

Replace it

The display is badly
connected to the board

Check the correct connection

The machine is on, the
selection starts regularly but
neither water nor ingredients
are dispensed

The power fuse (24 V) on
the board is burnt out

Replace it

MAN1260007 V.1 – 18/12/2014

Содержание Horeca Large 380


































Результаты поиска

Содержание Horeca Large 380

Отзывы:

Бренды по названию

Популярные бренды

Rheavendors Group Horeca Large 380, Руководство по установке и обслуживанию

Результаты поиска

Содержание Horeca Large 380

Отзывы:

Бренды по названию

Популярные бренды