RFM SEM910 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 33

background image

SEM910

Complete the assembly by placing the connector in the slot in one of the shell halves. Install the
two retaining screws on both sides of the shell and through the holes on both sides of the
connector; place the other shell half over the connector so the connector lies in the shell slot.
Secure the connector shell halves with the nuts and bolts provided.

Refer to the figures below.

Pinned connector in bottom connector shell

Completed connector with top connector shell
attached.

Attaching Remote Radio Connector – SEM910DX

The figure below shows the pin numbering of the Phoenix Contact, 16 pin, 3.81mm Remote
Radio connector (P/N1803714). The view provided is facing the side of the connector with the
screw heads showing.

The cable comes with pins pre-crimped onto the conductors and is assembled by inserting a
crimped pin into a hole location, then tightening the screw to hold the pin securely. To verify the
pin is held firmly in place, gently pull on the conductor wire.

©

2000- 2004 Cirronet

™

Inc

8

M-910-0003 Rev -

«
...
9
10
11
12
13
...
»

Содержание SEM910


































Отзывы:

Нет отзывов

Похожие инструкции для SEM910

TotalStorage SAN16M-R SAN

Бренд: IBM Страницы: 116

BladeCenter Management Module

Бренд: IBM Страницы: 184

InvenSense RoboKit1

Бренд: TDK Страницы: 13

Бренд: BWI Страницы: 5

Бренд: Zhone Страницы: 2

Бренд: National Instruments Страницы: 26

Бренд: Alcatel Страницы: 4

Бренд: Transition Networks Страницы: 5

Бренд: Airlinkplus Страницы: 24

Бренд: Brickcom Страницы: 184

Бренд: Valcom Страницы: 4

Бренд: ZyXEL Communications Страницы: 1

Бренд: Paradyne Страницы: 216

Бренд: Panduit Страницы: 5

Бренд: LevelOne Страницы: 77

Бренд: Panasonic Страницы: 277

Бренд: Panasonic Страницы: 438

Бренд: X-Micro Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды