background image

 

0603RHC4-JLGBEN 

9

/

21 

The 90° elbow, sealing ring, terminal and the 
combustion air inlet protection grill must be installed 
according to figure 7.   
All sealings must be correctly placed in the tubes to 
avoid flowing back of combustion products to the 
burner

 
As indicated, the combustion air inlet protection grill 
(PN 90 79050) must be integrated in the side panel of 
the controls compartment.  The dimensions of the 
required opening in this side panel and its position 
relative to the mounting flange of the RHC 4000(M) 
RJL heat exchanger enclosure are indicated in figure 
8 & 9.  
 
The air inlet protection grill must be installed in a level 
plane and horizontally centred. 
The minimum and maximum distances between the 
axis of the flue outlet pipe and the top of the 
combustion inlet grill are indicated in figure 9. 

Ensure the combustion inlet grill at the control door 
panel is completely sealed to prevent ingress of 
water. 
It is forbidden to use the combustion inlet grill as 
passage for cables or gas supplies.  Ensure the 
inlet grill openings are not obstructed. 
 
Make sure the installation of the combustion inlet 
grill is securely fixed. 
 
The outlet combustion sealing ring (dia 100 or 130) 
(PNs 06 22786 104 or 06 22786 134) must be 
installed in the fixed outlet panel of the air handler 
in a hole with dia 112mm for dia 100mm outlet or 
with hole diat dia 142mm for dia 130mm outlet.  
This hole must be located in the axis of the 90° flue 
outlet elbow with a sealing ring of the RHC 
4000(M) RJL (see drawing figure 9).  The sealing 
ring provided, fits for 1mm thick panels. 

 
Figure 7. :General arrangement combustion air inlet and flue products outlet for RHC 4000(M) RJL units

 

 

 

Figure 8 

 

 

* PN combustion air inlet protection grill : 90 79050 

Assure the sealing of the combustion air inlet grill to the controls 
compartment side panel is water tight 

Содержание RHC 4000 DJL Series






















Отзывы: