Reynolds Building Systems the Easton Скачать руководство пользователя страница 18

Страница: 18 / 20

Step 15 Install 1x6 Fascia & Roof Sheathing

Install (3) three 81" long 1x6 fascia boards on the soffit boxes with the beveled edge flush

with the top of the soffit blocks. Use 8d galv. nails.

Install 1x6 fascia boards on the front soffit boxes.

Install a 4'x6' roof sheathing panel with the bottom edge flush with the face of the 1x6

fascia. Make sure the trusses are plumb and the roof sheathing meets the center of the truss.

Use 7d sinkers spaced 12" apart.

Install the remaining roof sheathing per layout below. The top row of roof sheathing will be

about 1" below the ridge to allow for optional ridge venting.

1x6 Fascia Board

Install (2) two 1x3x73-1/4" boards along each side of the front door opening. Tack these

boards with a couple nails; you may want to move the trim later when you install the doors.

48" x 75"

48" x 72"

48" x 48"

37"x 51"

48" x 48"

Back Wall Panels

4X6 Sheathing

straight edge

37" x 72"

37"x 48"

37" x 72"

Содержание the Easton





















Результаты поиска

Содержание the Easton

Отзывы:

Похожие инструкции для the Easton

Бренды по названию

Популярные бренды

Reynolds Building Systems the Easton, Инструкция по сборке

Результаты поиска

Содержание the Easton

Отзывы:

Похожие инструкции для the Easton

Бренды по названию

Популярные бренды