background image

Cut the siding flush with the
bottom plate if installing the
building on a concrete slab.

A

B

X

X

X

X

X

X

X

X

X

X

C

72" Wall Plate

48" Wall Plate

:

:

: :

:

:

:

.

.

.

Step 6A Assemble 10' Side Walls

4.

Square wall frame. Measure diagonally (corner to corner); the measurements will be the same

when the wall is square.

5.

Cut one of the 48" wide siding panels in half lengthways. Select the half, with the 'tongue'

edge, and install this panel with the 'cut' edge flush with the end of the wall and extending 3/4"
below the bottom plate. Use 6d galvanized nails spaced 8" apart. LAP edge panel will be used

in next step.

6.

Install (2) two more siding panels.

Siding Extends 3/4" Below Plate

LAP Edge

1.

Position (2) two 2x4-48" boards and (2) two 2x4-72" boards together and indicate with 'X'

marks where the wall studs will be located. Mark the ends that will butt together with the letters

'A' and 'B'. Mark right side end with a 'C'. This will be referenced in a latter step.

2.

Install (7) seven 80-1/4" long wall studs between the wall plates. Use (2) two 10d sinkers

at each end of stud. Nail the frames together with (4) four 10d sinkers on each side.

3.

Repeat to assemble (3) three more 10' long side wall frames. You will need to cut (2) two

64" long 2x4s to a length of 48" to assemble the last 48" wall frame.

7.

Select (1) one of the 10' wall frames and repeat steps 4-6 to apply siding.

24"

23-1/4"

72" Wall Plate

48" Wall Plate

23-1/4"

Cut Edge

Tongue Edge

C

A

B

B

A

C

B

A

Содержание Best Barns Denver





















Отзывы: