REVELL Control TEXTER, Руководство пользователя

Страница: 8 / 22

English English
14 15
3 INSERTINg BaTTERIES (REMOTE CONTROl)
3A Slide the knob in the
"UNLOCK" direction and
remove the battery
compartment cover
3B Insert 4 x 1.5 V AA batteries
and pay attention to the polar-
ity, as shown in the battery
compartment.
3C Fit the cover on
again and slide the
knob in the "LOCK"
direction.
6 TRIM aDJuSTMENT OF THE CONTROl
The correct trimming is a basic requirement for achieving fault-free flying from the
helicopter. Its adjustment is simple, but it requires some patience and a feel for it.
Please observe the following instructions precisely: Carefully move the thrust control
up and raise the helicopter approximately 0.5 to 1 metre in altitude.
Briefly tap the buttons for the counter-rotating trim to the left until the helicopter no
longer rotates by itself. Do not simply actuate the trim buttons continuously.
6A If the helicopter quickly or slowly rotates clockwise by itself…
Briefly tap the buttons for the counter-rotating trim to the right until the helicopter no
longer rotates by itself. Do not simply actuate the trim buttons continuously.
6B If the helicopter quickly or slowly rotates anti-clockwise by itself…
1A Counter-rotating rotor
blades
1B Stabiliser
1C Tail rotor
1D LED headlamp
1E Mini USB PORT
1F ON/OFF switch
1G Charge socket
1 HElICOPTER
2A ON/OFF switch
2B Control for thrust
2C Left/right trim
2D Control for forward and
backwards flight as
well as rotation
2E ON/OFF button for LEDs
2F Speed button
2G USB port
2 REMOTE CONTROl
4 CHaRgINg THE HElICOPTER
Attention: The battery and motor must cool down for 10 to 15 minutes before
charging and after every flight. Otherwise they can be damaged. The charging process
must be constantly monitored. Always ensure that the charging process takes place on
a fireproof surface in a fire-resistant environment.
• Plug the USB charger into an open USB port
(4A) .
• Carefully insert the charging cable in the charge socket of the helicopter (4B) .
The plug must be gently inserted into the charging socket – DO NOT USE FORCE.
If the plug is not correctly inserted into the charging socket, the helicopter may
become damaged and, under certain circumstances, become an injury risk.
• Now switch on the helicopter. The front LED search headlamp begins to blink (4C) .
When the charging process is complete, the LED search headlamp illuminates
continuously. Now switch the Power switch to "OFF" and disconnect the charging
cable from the helicopter and from the USB port.
You can also use the USB port on the remote control:
• Switch off the helicopter and the remote control.
• For this purpose, plug the USB charger into the USB port of the remote control (4D) .
• Now carefully insert the charging cable in the charge socket of the model (4B) . The
plug must be gently inserted into the charging socket – DO NOT USE FORCE. If the
plug is not correctly inserted into the charging socket, the helicopter may become
damaged and, under certain circumstances, become an injury risk.
• Now switch the remote control "ON" and the Power LED begins to blink. Slowly move
the thrust control to full throttle and back to the starting position. Now the Power LED
illuminates green continuously.
• The Power LED goes out when the charging process is completed. Disconnect the
helicopter from the charger and disconnect the charger from the USB port once
charging is completed.
The helicopter can fly for approx. 6-8 minutes after a charge time of
approx. 50 minutes.
Warning notice:
The LiPo battery does not normally heat up while charging. If it
should become hot and/or changes to the surface begin to appear, immediately
discontinue the charging process!
INSTRuCTIONS FOR SaFE FlYINg
GENERAL FLYING TIPS:
• Always place the helicopter on a level
surface. An inclined surface can, under
certain circumstances, negatively effect
the helicopter during take-off.
• Always operate the controls slowly and
with a gentle touch.
• Always maintain visual contact with the
helicopter and do not look at the remote
control!
• Move the thrust controller somewhat
down again once the helicopter has
lifted off from the ground. Maintain
flying altitude by adjusting the thrust
controller.
5 STaRT PREPaRaTION
The thrust controller (the left controller on the remote control) must point down
before being switched on
(5A)
. Then set the remote control's ON/OFF switch to "ON"
(5B) . The power LED begins to blink. Now set the helicopter's ON/OFF switch to the
"ON"
(5C)
. Place the helicopter on the ground so that the tail points toward you
(5D)
.
Activate the remote control moving the thrust controller to maximum and then back
to its starting position. The power LED will now remain permanently illuminated green,
signalling that the helicopter is connected to the remote control and ready for flight.
Note: Only minimal corrections of the controls are necessary for a smoothing flying
behaviour of the helicopter!
7B Land or decrease altitude by moving
the control for thrust backward. Only
minimal corrections to the controller are
necessary to ensure smoothing flying of
the helicopter!
7D Fly backwards by carefully moving
the controller for forward and backwards
flight as well as rotation backwards.
7F Turn helicopter around to the right by
moving the controller for forward/back-
ward flight and rotation to the right.
7A Take off or increase altitude by
carefully moving the control for thrust
forward.
7C Fly forward by carefully moving the
controller for forward and backwards
flight as well as rotation forward.
7E Turn helicopter around to the left by
moving the controller for forward/back-
ward flight and rotation to the left.
7 FlIgHT CONTROl 7 FlIgHT CONTROl